The design of non-rail vehicles shall be coordinated with the boarding platforms to minimize the gap between the vehicle floor and the boarding platforms....
Search Results "Extended Floor Surface"
Filters
Commonly Searched Documents
-
T404.2 Vehicle Floor and Boarding Platform Coordination
-
11B-407.2.3.1 Floor designation
A raised star, placed to the left of the floor designation, shall be provided on both jambs at the main entry level. ...
-
Pilot Rock TQ700 Square Frame Square Utility Table
Surface mount installation only (Anchor bolts not included - use Model ANC3-4 Anchor Kit). FINISH: All steel frame components have a powder coat finish in your choice of color....
-
Pilot Rock T700 Square Frame Rectangular Utility Table
Surface mount installation only (Anchor bolts not included - use Model ANC3-4 Anchor Kit). FINISH: All steel frame components have a powder coat finish in your choice of color....
-
KirbyBuilt Providence Picnic Table with Maximum Seating
100" l x 61.25" w x 32" h TableTop Dimensions 72" l x 48" w x 32" h Seat Dimensions 72" & 48" l x 9.5" w x 18" h Mount Type Portable/Surface...
-
A5.1 General
Dining counters (where there is no service) are typically found in small carry-out restaurants, bakeries, or coffee shops and may only be a narrow eating surface attached to a wall....
-
R&D Workshop Trim-A-Slab Expansion Joint Repair
Trim-A-Slab is a replacement for rotted and old wood typically found between slabs in driveways and sidewalks. This wood was used during the slab construction, and is part of the...
-
Stabilizer Solutions StaLok Stabilizer Joint Sand
STABILIZED JOINT SAND THAT STAYS PUT BETWEEN PAVERS StaLok Paver Sand sets up strong and locks in between pavers. It allows water to drain and ‘heals’ itself. The sand repairs...
-
GAP ARMOUR
GAP ARMOUR IS AN INNOVATIVE RUBBER MATERIAL ...that easily installs (with a rubber hammer) into open concrete expansion joints to completely seal and protect! Gap Armour can be...
-
Handrails Along Walkways
Handrails Along Walkways. The 1991 Standards do not contain any technical requirement for handrails provided along walkways that are not ramps. Section 403.6 of the 2010 Standards...
-
1017.7 Slopes
The slopes of trails shall comply with 1017.7.
-
Slope Ratio
Slope Ratio—A ratio of vertical distance to horizontal distance or rise to run.
-
Trail Construction Techniques
Information that is already available to Forest Service employees is not repeated in this guidebook. The "Trail Construction and Maintenance Notebook" includes practical techniques...
-
2. Methodology
[See subsections ...]
-
1017.7 Slopes
The slopes of trails shall comply with 1017.7.
-
Range or Cooktop: ADA Standard Section 804.6.4
Where a forward approach is provided, the clear floor or ground space shall provide knee and toe clearance complying with 306....
-
11B-804.6.4 Range or cooktop
Where a forward approach is provided, the clear floor or ground space shall provide knee and toe clearance complying with Section 11B-306....
-
A4.23.3 Clear Floor Space
Since the shower does not have a lip, the floor space can be used for required maneuvering space....
-
11B-407.2.3.1 Floor designation
Floor designations complying with Sections 11B-703.2 and 11B-703.4.1 shall be provided on both jambs of elevator hoistway entrances....
-
11B-407.2.3.1 Floor designation
Floor designations complying with Sections 11B-703.2 and 11B-703.4.1 shall be provided on both jambs of elevator hoistway entrances....
-
5.4.8 Transfer Support Gripping Surface Hazard for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.8 Transfer Support Gripping Surface Hazard for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
Pilot Rock Square Frame Square Table - Series TQ703
Surface mount installation only (Anchor bolts not included). Use Model ANC3-4 Anchor Kit. FINISH: All steel frame components have a powder coat finish in your choice of color....
-
1133A.2, Item 3
A clear floor space at least 30 inches (762 mm) by 48 inches (1219 mm) that allows either a parallel or a forward approach shall be provided at the work surface required by Section 1133A...
-
1133A.2, Item 3
A clear floor space at least 30 inches (762 mm) by 48 inches (1219 mm) that allows either a parallel or a forward approach shall be provided at the work surface required by Section 1133A...
