R304.5.3 Cross Slope. The cross slope of curb ramps, blended transitions, and turning spaces shall be 2 percent maximum. At pedestrian street crossings without yield or stop control...
Search Results "Concrete Surface"
Filters
Commonly Searched Documents
-
R304.5.3 Cross Slope
-
Addendum F: Relative Height Differences
Relative heights were calculated for high and low transfers for all three protocols. Refer to Addendum A for the definition of relative height. The following tables F1-F3 represent...
-
1133A.4.1, Item 3
3. The sides of adjacent cabinets and the back wall, which may become exposed to moisture or food handling when a countertop is lowered, shall be constructed of durable, nonabsorbent...
-
1014.3 Floor
The floor within camp shelters shall comply with 1014.3.
-
1.1.12 Ramp cross slope
1.1.12 Ramp cross slope. Measure for overall cross slope of ramps by establishing elevations at the extreme edges of the ramp at the top and bottom of the ramp and calculate the...
-
1133A.4.1, Item 3
3. The sides of adjacent cabinets and the back wall, which may become exposed to moisture or food handling when a countertop is lowered, shall be constructed of durable, nonabsorbent...
-
4.8.5* HANDRAILS
(2) If handrails are not continuous, they shall extend at least 12 in (305 mm) beyond the top and bottom of the ramp segment and shall be parallel with the floor or ground surface....
-
M305.2.6 Gripping Surfaces (Section-by-Section Analysis)
The proposed rule did not provide any specific requirements regarding gripping surfaces on transfer supports....
-
11B-805.7 Built-in cabinets and work surfaces
Built-in cabinets, counters and work surfaces shall be accessible, including: patient wardrobes, nurse’s stations, administrative centers, reception desks, medicine preparation areas, laboratory...
-
§ 35.151(f)(1)
sleeping rooms) or on floors containing accessible sleeping rooms with mobility features shall provide turning spaces that comply with section 809.2.2 of the 2010 Standards and kitchen work surfaces...
-
19 Inch Low Height
transfer surface....
-
M305.3.1 Horizontal Position
Where the support is horizontal, the top of the gripping surface shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum above the standing surface....
-
M301.2.1 Adjustability
Transfer surfaces shall be adjustable in height measured from the floor to the top of the uncompressed transfer surface and shall provide the following: A....
-
4.6.5 PASSENGER LOADING ZONES
Vehicle standing spaces and access aisles shall be level with surface slopes not exceeding 1:50 in all directions....
-
M305.3.1.3 Vertical Position
The length of the gripping surface on vertical standing supports shall be 18 inches (455 mm) minimum....
-
4.6.6 Passenger Loading Zones
Vehicle standing spaces and access aisles shall be level with surface slopes not exceeding 1:50 (2%) in all directions....
-
T402.9 Transitions
Vertical surface discontinuities at transitions from boarding and alighting areas to ramps and bridgeplates shall comply with T302.4....
-
M305.2.2.2 Side Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.2 shall be 28 inches (710 mm) long minimum and shall be positioned along the width of transfer surfaces....
-
11B-813.2.1.2 Clearance
Floor or ground surfaces of clearances shall comply with Section 11B-302. Changes in level are not permitted....
-
Adaptive Surfing Makes the Ocean Accessible for People Who Use Wheelchairs - Rolling On, Episode 5
See how Arianny Ramirez rides Rockaway Beach’s waves on a surfboard—even though she needs a wheelchair to get around on land. Go to g.co/LGa11y and find out how Local Guides can make...
-
17 Inch Low Height
The safest and most easily accessible transfers are those with no or very little horizontal and vertical distance between the seat of the wheelchair and the transfer surface....
-
M305.2.1.2 Side Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.2 shall be capable of supporting transfer on each side of the transfer surface....
-
5.2 Transfer Surface Size for Equipment Used by Patients in Supine, Prone, or Side-Lying Position
5.2 Transfer Surface Size for Equipment Used by Patients in Supine, Prone, or Side-Lying Position....
-
4.9.4 HANDRAILS
At the top, the extension shall be parallel with the floor or ground surface....
