Changes in height greater than ½ inch (12.7 mm) shall be accomplished by means of a ramp complying with Section 1114A or by means of a platform constructed to the level of the floor as illustrated...
Search Results "Built-Up Curb Ramp"
-
1132A.4, Item 3
-
4.1.2(5)
EXCEPTION: Accessible ramps complying with 4.8 or, if no other alternative is feasible, accessible platform lifts complying with 4.11 may be used in lieu of an elevator....
-
1132A.4, Item 3
Changes in height greater than ½ inch (12.7 mm) shall be accomplished by means of a ramp complying with Section 1114A or by means of a platform constructed to the level of the floor as illustrated...
-
Hussey Seating Company Roll-A-Way Seating
Four swivel casters are mounted on hinged plates to either fold underneath for easy mobility or fold up out of the way when secured to the floor....
-
505.4 Height
Top of gripping surfaces of handrails shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum vertically above walking surfaces, stair nosings, and ramp surfaces....
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
seca 676 r Digital Wheelchair Scale with Handrail and Integrated RS232 Interface
Two ramps included. Pre-TARE function with three memory cells....
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
Common Questions (Passenger Loading Zones)
Common Questions
-
Cross Slope and Surfaces [4.8.6]
Ramp surfaces must comply with requirements for ground and floor surfaces and be "stable, firm, and slip-resistant." A specific level of slip-resistance is not mandated....
-
11B-406.2.2 Sides of curb ramps
Where provided, curb ramp flares shall not be steeper than 1:10. FIGURE 11B-406.2.2 ‡‡ SIDES OF CURB RAMPS...
-
5.9.2 Standing Supports on Ramped Entry Raised Platforms with Wheelchair Spaces
5.9.2 Standing Supports on Ramped Entry Raised Platforms with Wheelchair Spaces....
-
seca 684 r Digital Multifunctional Scale with Integrated RS232 Interface
Ramp seca 470 included. TARE, Auto-HOLD and damping function. Integrated transport castors allow for easy mobility....
-
5.8.1.2.2 Single Ramped Entry - Edge Protection on the Platform and Platform Sides Recommendations
5.8.1.2.2 Single Ramped Entry - Edge Protection on the Platform and Platform Sides Recommendations The Committee recommends a two-inch high edge protection on the back of the platform...
-
Problem Three (Accessible Route)
Solution: Install a portable ramp....
-
EZ-ACCESS Transitions® Modular Entry Mat Video
Requires the Registered User plan or above. Login! -
Re: SCOTT JOHNSON v. STARBUCKS CORPORATION - AMICUS BRIEF
I think it's interesting to notice that his amicus is responding to a specific request from the court about a specific section of the ADA Standards. Notice that it does not address...
-
11B-505.9 Fittings
Handrails shall not rotate within their fittings.
-
505.9 Fittings
Handrails shall not rotate within their fittings.
-
505.9 Fittings
Handrails shall not rotate within their fittings.
-
505.9 Fittings
505.9 Fittings. Handrails shall not rotate within their fittings.
-
4.8.4(4)
(4) If a doorway is located at a landing, then the area in front of the doorway shall comply with 4.13.6.
-
505.9 Fittings
Handrails shall not rotate within their fittings.
