following conditions are met: a) base cabinets can be removed without the use of specialized tools or knowledge; b) the finish floor extends under the base cabinet; and c) the walls...
Search Results "Transfer Wall"
Filters
Commonly Searched Documents
-
11B-809.9.3 Removable base cabinets
-
M1
.), is a sign with raised characters and Braille mounted on the wall adjacent to the latch side of the door and centered 60 inches above the floor?...
-
Problem Two (Protruding Objects)
Problem Two: A wall-mounted display case protrudes seven inches from the wall and the bottom of the case is 40 inches above the floor....
-
Adjustable height protocol
,96%] of the sample (107/116) could transfer at a height of 22” (50.8cm)....
-
711.3.1 Through penetrations
Through penetrations of fire-resistance-rated walls shall comply with Section 711.3.1.1 or 711.3.1.2....
-
2.2.4 Maneuverability
tasks: • 90-degree turn, • 180-degree turn with no restrictions on length of the maneuver, • 180-degree with a center barrier, • 360-degree rotation within a space with four walls...
-
6.1 Deliberative Process
At its first meeting, the Advisory Committee considered this NPRM recommendation of 17” to 19”, which applied to either fixed or adjustable height transfer surfaces....
-
Meeting ANSI Standard S12.60 Requirements
the wall height increases above ten feet....
-
Spectrum Aquatics Gallatin Water Powered Assisted Access Lift
The standard unit will accommodate anchor locations of 18″ to 30″ from the pool wall. ...
-
American Standard Acrylic Seated Safety Shower
Fully open on one side, the wide seat allows for easy transfer in and out of the shower. The low 3" threshold and a wrap-around grab bar further enhance safety in the shower....
-
11B-609.3 Spacing
of 6 inches on either side of the inside corner between two adjacent wall surfaces....
-
11B-609.3 Spacing
of 6 inches on either side of the inside corner between two adjacent wall surfaces....
-
11B-609.3 Spacing
of the inside corner between two adjacent wall surfaces....
-
H21
Is a horizontal grab bar at least 40 inches long securely mounted on the adjacent side wall 33 to 36 inches above the floor with one end no more than 12 inches from the back wall 33 to 36...
-
11B-610.3.1 Rectangular seats
The rear edge of a rectangular seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (381 mm) minimum and 16 inches (406 mm) maximum from the seat wall....
-
Recessed Doors and Gates: ADA Standard Section 404.2.4.3
Section 404.2.4.3 covers the current ADA Standards for maneuvering clearances at recessed doors and gates.
-
Bathtub Seats: ADA Standard Section 610.2
Section 610.2 covers the current ADA Standards for bathtub seats.
-
Alteration
restoration, resurfacing of circulation paths or vehicular ways, changes or rearrangement of the structural parts or elements, and changes or rearrangement in the plan configuration of walls...
-
11B-201.3 Temporary and permanent structures
facilities covered by these requirements include, but are not limited to, reviewing stands, temporary classrooms, bleacher areas, stages, platforms and daises, fixed furniture systems, wall...
-
11B-610.2 Bathtub seats
Permanent seats at the head end of the bathtub shall be 15 inches (381 mm) deep minimum and shall extend from the back wall to or beyond the outer edge of the bathtub....
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware. ◼...
-
11B-903.6 Structural strength
Benches shall be affixed to the wall or floor....
-
5. Exception from the Requirements of M302 for Weight Scales with Integral Seats
One of these commenters explained that not all people with disabilities who need to transfer are wheelchair users and some wheelchair users may choose to transfer, even if the device is...
-
Murdock Manufacturing Barrier-Free 14-Gage Stainless Steel Bi-Level Wall Mount Water Cooler
A172.8FGVR Series is a self-contained, pressure bi-level water cooler. The each unit delivers a minimum of 8.0 gph (30.3 lph) of water at 50°F (10°C) cooled from 80°F (26.7°C) inlet...
