In residential dwelling units required to comply with Section 11B-809, at least one 30 inches (762 mm) wide minimum section of counter shall provide a kitchen work surface that complies...
Search Results "Ground Surface"
Commonly Searched Documents
-
11B-804.3 Kitchen work surface
-
5.1 Transfer Surface Height
5.1 Transfer Surface Height...
-
National Network of ADA Centers
The height of the transfer surface during patient transfer shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum measured from the floor to the top of the transfer surface....
-
11B-240.1 General
In existing play areas, where play components are relocated for the purposes of creating safe use zones and the ground surface is not altered or extended for more than one use zone, the...
-
11B-240.1 General
In existing play areas, where play components are relocated for the purposes of creating safe use zones and the ground surface is not altered or extended for more than one use zone, the...
-
11B-240.1 General
In existing play areas, where play components are relocated for the purposes of creating safe use zones and the ground surface is not altered or extended for more than one use zone, the...
-
§ 35.150(b)(4)(i)
(i) In addition to the provisions of section 240.2.1 of the proposed standards, where an existing play area provides elevated play components, an additional number of ground level play components...
-
Built-in Elements
BUILT-IN ELEMENTS Dining/work surfaces 11B-226, 11B-902.2 Benches 11B-903.2...
-
Built-in Elements
BUILT-IN ELEMENTS Dining/work surfaces 11B-226, 11B-902.2 Benches 11B-903.2...
- Filter Pave™ Porous Paving for Stormwater Management
-
Accessible Route to Play Components
Section 206.2.17 of the 2010 Standards provides scoping requirements for accessible routes to ground level and elevated play components and to soft contained play structures....
-
226.1 General
Where dining surfaces are provided for the consumption of food or drink, at least 5 percent of the seating spaces and standing spaces at the dining surfaces shall comply with 902....
- SafePath SAFELIFT™ Platform Weightlifting Surface
-
810.5.1 Slope
810.5.1 Slope. Rail platforms shall not exceed a slope of 1:48 in all directions. EXCEPTION: Where platforms serve vehicles operating on existing track or track laid in existing...
-
810.5.1 Slope
Rail platforms shall not exceed a slope of 1:48 in all directions. EXCEPTION: Where platforms serve vehicles operating on existing track or track laid in existing roadway, the...
-
11B-810.5.1 Slope
Rail platforms shall not exceed a slope of 1:48 in all directions. Exception: Where platforms serve vehicles operating on existing track or track laid in existing roadway, the...
-
810.5.1 Slope
Rail platforms shall not exceed a slope of 1:48 in all directions. EXCEPTION: Where platforms serve vehicles operating on existing track or track laid in existing roadway, the...
-
R407.6.1 Slope
R407.6.1 Slope. Landing slopes shall be 2 percent maximum in any direction.
-
R407.3 Cross Slope
R407.3 Cross Slope. The cross slope of ramp runs shall be 2 percent maximum.
-
Wayfinding is more than just graphics (slides 2 – 4)
Cognitive process (slides 2 - 4). [Wayfinding is] really more of a cognitive process. You gather information at the beginning. You cite and execute a path to take. And then you...
-
A. Slope at Door
A. If a fully automatic door is not provided, is the walkway in front of the lobby door level, without any portion steeper than 1:50 (critical dimension of ´" or less), so persons...
-
A4.13.9 Door Hardware
Some disabled persons must push against a door with their chair or walker to open it. Applied kickplates on doors with closers can reduce required maintenance by withstanding abuse...
-
A4.13.9 DOOR HARDWARE
Some disabled persons must push against a door with their chair or walker to open it. Applied kickplates on doors with closers can reduce required maintenance by withstanding abuse...
-
APPENDIX C
APPENDIX C On‐Site Inspection Form ETA Editor's Note Click here to download the pdf version of the document with the ON-SITE INSPECTION FORM in APPENDIX C, pdf page 41.