The running slope of walking surfaces shall not be steeper than 1:20. The cross slope of walking surfaces shall not be steeper than 1:48....
Search Results "Surface Material"
Filters
Commonly Searched Documents
-
11B-403.3 Slope
-
11B-405.4 Floor or ground surfaces
Floor or ground surfaces of ramp runs shall comply with Section 11B-302. Changes in level other than the running slope and cross slope are not permitted on ramp runs....
-
11B-411.4.2 Floor surfaces
Floor surfaces in elevator cars shall comply with Section 11B-407.4.2....
-
11B-409.4.2 Floor surfaces
Floor surfaces in elevator cars shall comply with Sections 11B-302 and 11B-303....
-
902 Dining Surfaces and Work Surfaces
Section 902 provides specifications for seating at dining and work surfaces....
-
226 Dining Surfaces and Work Surfaces
Provisions for access to dining and work surfaces have been revised to: further define dining surfaces as those used "for the consumption of food or drink" (226.1) clarify...
-
Acceptable Trail Surfacing Requirements
Trail surfaces are currently considered accessible only if the surfacing material is firm, stable, and slip-resistant and the trail has the engineered attributes of adequate width, moderately...
-
Surfaces: ADA Standard Section 505.8
Section 505.8 covers the current ADA Standards for handrail gripping surfaces and also any adjacent surfaces to them.
-
Carpet: ADA Standard Section 302.2
Section 302.2 covers the current ADA Standards for carpet.
-
11B-302.2 Carpet
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge. Carpet edge trim shall comply with Section 11B-303....
-
Dining Surface and Work Surface
Commenters expressed concern about use of the terms "dining surfaces" and "work surfaces" and urged the Board to include definitions of the terms in the final rule....
-
4(6)
(6) At the primary entry door to dwelling units with direct exterior access, outside landing surfaces constructed of impervious materials such as concrete, brick or flagstone, are no more...
-
Producing Printed Material in Large Print
Large print material can be produced by using a photo copier or a computer where an 18-point type size or larger can be selected....
-
T402.5 Surfaces
Ramp and bridgeplate surface material shall comply with T302 and extend across the full width and length of the ramp or bridgeplate....
-
Surface, Slope, and Openings [1011.2.2, 1011.2.3, and 1011.2.4]
The surface of the clear ground space must be firm and stable. Additional information on firm and stable surfaces is provided in the trails section of this guide....
-
General: ADA Standard Section 302.1
Section 302.1 of the ADA Standards covers information in the current ADA Standards for floor or ground surfaces.
-
Floor and Ground Surfaces
This guide explains requirements in the ADA Standards for floor and ground surfaces. ...
-
T302.4 Surface Discontinuities
Surface discontinuities shall be ½ inch (13 mm) high maximum and shall be beveled with a slope not steeper than 1:2. EXCEPTIONS: 1....
-
1015.5 Surface
This section requires the surface of the clear ground space and turning space to be firm and stable....
-
Check Writing Surfaces: ADA Standard Section 904.3.3
Where provided, check writing surfaces shall comply with 902.3....
-
11B-505.8 Surfaces
Handrail gripping surfaces and any surfaces adjacent to them shall be free of sharp or abrasive elements and shall have rounded edges....
-
Site Profiles by Surface Type
Some playground sites were surfaced with one surface material/system while others were surfaced with a combination of two surface materials/systems. ...
-
SafeLane® Surface Overlay in Action
Protecting people, roads and infrastructure, SafeLane® surface overlay from Cargill Deicing Technology is the only pavement overlay with anti-icing capabilities....
-
3.2.3 Surface
The ground surface in all camp living areas shall be firm and stable. The type of surface should be appropriate to the setting and level of development....
