The technical requirements for walking surfaces include provisions on slip resistance, the maximum size of surface openings, and the maximum height of vertical surface discontinuities (i.e...
Search Results "Side Transfer Surface"
-
T302 Walking Surfaces
-
11B-306.3.3 Minimum required depth
At dining and work surfaces required to be accessible by Section 11B-226.1, knee clearance shall extend 19 inches (483 mm) deep minimum at 27 inches (686 mm) above the finish floor or ground...
-
11B-306.3.3 Minimum required depth
At dining and work surfaces required to be accessible by Section 11B-226.1, knee clearance shall extend 19 inches (483 mm) deep minimum at 27 inches (686 mm) above the finish floor or ground...
-
M303.2.5 Surfaces (Section-by-Section Analysis)
The MDE NPRM proposed to require diagnostic equipment used by patients seated in a wheelchair to provide a wheelchair space with a surface that does not slope more than 1:48 in any direction...
-
4.2.2 Cooking Surface Height
The cooking surface shall be at least 15 inches (380 mm) and no more than 34 inches (865 mm) above the floor or ground surface. ...
-
809.2.1.2 Floor Surfaces
809.2.1.2 Floor Surfaces This section specifies that carpet not be provided on floor surfaces in emergency transportable housing units with mobility features....
-
RECOMMENDATIONS
RECOMMENDATIONS An objective test procedure for measuring the firmness and stability of surfaces with a portable device and performance specifications need to be accepted in order to...
-
Exposed Pipes and Surfaces [4.19.4]
Exposed Pipes and Surfaces [4.19.4] To prevent burns, hot water pipes and drain pipes under lavatories must be insulated or otherwise configured to protect against contact....
-
606.5 Exposed Pipes and Surfaces
606.5 Exposed Pipes and Surfaces. Water supply and drain pipes under lavatories and sinks shall be insulated or otherwise configured to protect against contact....
-
4.7.10 DIAGONAL CURB RAMPS
If diagonal curb ramps have flared sides, they shall also have at least a 24 in (610 mm) long segment of straight curb located on each side of the curb ramp and within the marked crossing...
-
4.16.4 Grab Bars
including diameter, spacing, and structural strength (ADAAG 4.26) and for toilets in particular, including length and positioning, only the latter two were adjusted to accommodate assisted transfers...
-
804.3 Kitchen Work Surface
804.3 Kitchen Work Surface....
-
1d
Does the 36" x 48" clear floor space directly outside the shower extend at least 12" past the seat wall of the shower to allow for a seat-to-seat transfer from the wheelchair?...
-
408.4.2 Floor Surfaces
408.4.2 Floor Surfaces. Floor surfaces in elevator cars shall comply with 302 and 303....
-
What should I do if my staff do not know how to help a person with a disability transfer or know what the ADA requires my office to do?
Q What should I do if my staff do not know how to help a person with a disability transfer or know what the ADA requires my office to do?...
-
6. Recognize that Proper Installation of Play Surface Systems is Key
Recognize that Proper Installation of Play Surface Systems is Key An accessible surface system can be rendered useless if it is not properly installed....
-
Aluminum Swaged SG Series Pressure-Locked Grating
Slip resistant & serrated surfaces also available....
-
4.7.10 Diagonal Curb Ramps
If diagonal curb ramps have flared sides, they shall also have at least a 24 in (610 mm) long segment of straight curb located on each side of the curb ramp and within the marked crossing...
-
Unity Surfacing Systems Soft-Land Rubberized Safety Surfacing
Soft-Land is "Unity's" 3", 3 1/4", 3 1/2" and 3 3/4" thick rubberized safety surfacing, flooring and paver products that are made from 100% recycled tires and rubber granules....
-
Aluminum Dove Tail Series Pressure-Locked Grating
Slip resistant & serrated surfaces also available....
-
Location: ADA Standard Section 703.4.2
Where a tactile sign is provided at a door, the sign shall be located alongside the door at the latch side....
-
1008.4.4 Entry Points and Seats
Where play components require transfer to entry points or seats, the entry points or seats shall be 11 inches (280 mm) minimum and 24 inches (610 mm) maximum from the clear floor or ground...
-
1008.4.4 Entry Points and Seats
Where play components require transfer to entry points or seats, the entry points or seats shall be 11 inches (280 mm) minimum and 24 inches (610 mm) maximum from the clear floor or ground...
