This depth measurement is from the center-point of the front and back of the transfer surface as shown in Figure 5.2.1.1....
Search Results "Measuring Technique"
Filters
Commonly Searched Documents
-
5.2.1.2 Transfer Surface Depth Recommendation for M301
-
Front grab bar protocol
The preferred grab bar height was measured between the floor and the top of the grab bar surface. ...
-
404.2.10 Door and Gate Surfaces
Swinging door and gate surfaces within 10 inches (255 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
Common Requirements (R304.5) (Section-by-Section Analysis)
The cross slope is measured perpendicular to the direction of pedestrian travel....
-
Carpet [4.5.3]
A pile thickness up to ½ inch (measured to the backing, cushion, or pad) is allowed, although a lower pile provides easier wheelchair maneuvering....
-
Bails et al.
Research findings from many of the field tests used pre-established sizes and features to measure barriers and problems....
-
11B-707.4 Privacy
., a covered entity does not have to take measures that would result in a fundamental alteration of its program or would cause undue burdens, provide adequate protection to operators of...
-
§ 38.175(a)
All doorways shall have, when the door is open, at least 2 footcandles of illumination measured on the door threshold....
-
11B-707.4 Privacy
., a covered entity does not have to take measures that would result in a fundamental alteration of its program or would cause undue burdens, provide adequate protection to operators of...
-
3.3.2 Experienced Clinicians
to formulate their comments to the Committee:X Committee members want to learn about common transfer methods, including information about mobility device positioning, transfer techniques...
-
M301.4.1 Clearance in Base (Section-by-Section Analysis)
The MDE NPRM proposed a clearance in the base of 44 inches wide minimum, 6 inches high minimum measured from the floor, and 36 inches deep minimum measured from the edge of the examination...
-
Visual Acuity
Well, visual acuity is just a measure of the limit of your vision resolution (slide 7). And this is what is called the ETDRS chart (slides 7 and 8)....
-
Boat Slips: ADA Standard Section 1003.2.1
The cross slope specified in 403.3 and 405.3 for gangways, transition plates, and floating piers that are part of accessible routes shall be measured in the static position. 8....
-
11B-1003.2.1 Boat slips
The cross slope specified in Sections 11B-403.3 and 11B-405.3 for gangways, transition plates, and floating piers that are part of accessible routes shall be measured in the static position...
-
11B-302.2 Carpet
A pile thickness up to 1/2 inch (13 mm) (measured to the backing, cushion, or pad) is allowed, although a lower pile provides easier wheelchair maneuvering....
-
AJW Architectural Products U133 56 oz. One-Piece Liquid Soap Dispenser - Surface Mounted
Neoprene seals and a stainless return spring will provide a pre-measured, drip free dispensing system. Valve cannot be removed without taking hex nut off....
-
Safepath EZ Edge™ Transition
If you need assistance acquiring these measurements, contact our full service design team and they will find the best solution that fits your specifications....
-
5.1 Overview of Legal Obligations
Tests must reflect the skills and aptitudes of an individual rather than impaired sensory, manual, or speaking skills, unless those are job-related skills the test is designed to measure...
-
1117B.5.6
Dots shall be 1/10 inch (2.54 mm) on center in each cell with 2/10-inch (5.08 mm) space between cells, measured from the second column of dots in the first cell to the first column of dots...
-
Slope
Slope is measured from ground level at the entrance to all arrival points within 50 feet, and is considered impractical only when it exceeds 10 percent between the entrance and all these...
-
Updates and Other Pocket Guides
For ADA survey and compliance tools that will simplify your field measurement process and plan reviews, http://www.adasurveytools.com/ has a growing collection of templates and tools you...
-
Height and Clearances [4.19.2]
Knee space at least 27 inches high must be at least 8 inches deep measured from the leading edge....
-
3.3.6 Knee Clearance Height, minimum
In the case of the U.S. and Canadian standards, however, the level of accommodation drops to 80% in relation to measured knee heights among wheelchair users in their respective countries...
-
2.3.4 Analysis of Door Use Difficulty
2.3.4 Analysis of Door Use Difficulty The measurement of door use performance was designed as a quasi-experimental study that involved systematically observing and coding WhMD user performance...
