A tape measure is used to measure the length, width, height, and depth of various elements including parking spaces and access aisles, routes, thresholds, doorways, and protruding objects...
Search Results "Coin Slot Height"
Filters
Commonly Searched Documents
-
Using the Tape Measure
-
§382.133(f)(3)
(3) The maximum weight and dimensions (length, width, height) of the device to be used by an individual that can be accommodated in the aircraft cabin consistent with the safety regulations...
-
703.5.4 Character Proportions
Characters shall be selected from fonts where the width of the uppercase letter "O" is 55 percent minimum and 110 percent maximum of the height of the uppercase letter "I"....
-
703.5.4 Character Proportions
Characters shall be selected from fonts where the width of the uppercase letter "O" is 55 percent minimum and 110 percent maximum of the height of the uppercase letter "I"....
-
703.2.4 Character Proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 55 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
703.5.4 Character Proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 55 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
703.6.1 Pictogram Field
Pictograms shall have a field height of 6 inches (150 mm) minimum. Characters and braille shall not be located in the pictogram field. Figure 703.6.1 Pictogram Field...
-
R410.10 Line Spacing
Spacing between the baselines of separate lines of characters within a message shall be 135 percent minimum and 170 percent maximum of the character height....
-
11B-705.1.1.2 Dome size
TITLE NOTES 11B-705.1.1.2 Dome size Aligns California Building Code dimensional requirements for detectable warning dome heights...
-
1133A.5 Lower shelving
Lower shelving and/or drawer space shall be provided in the kitchen at a height of no more than 48 inches (1219 mm) above the floor....
-
703.2.4 Character Proportions
Characters shall be selected from fonts where the width of the uppercase letter "O" is 55 percent minimum and 110 percent maximum of the height of the uppercase letter "I"....
-
Positioning
According to ADAAG, positioning is dependent on two factors, height and location of grab bars, both of which were altered by designers to better accommodate an older population....
-
Obstructed High Reach
Obstructions at side reaches are limited to a height of 34”....
-
§100.303(b)
(b) The following examples illustrate the application of paragraph (a) of this section: Example (1): John and Mary apply for housing at the Vista Heights apartment complex which is an...
-
3.3.15.2 Side (lateral) reach - unobstructed
reach - unobstructed For WhMD users in our study that could perform a reach task, over 90% of each of the WhMD user groups could reach beyond the lateral most point of their WhMDs for heights...
-
M305.3.2.1 Horizontal Position
The height of the top of the gripping surface on horizontal standing supports shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum above the standing surface....
-
§ 1194.25(j)(2)
(2) Where any operable control is 10 inches or less behind the reference plane, the height shall be 54 inches maximum and 15 inches minimum above the floor....
-
704.6 Structural stability
The wall shall extend to the height required by Section 704.11 and shall have sufficient structural stability such that it will remain in place for the duration of time indicated by the...
-
1017.5 Tread Obstacles
Tread obstacles on trails, passing spaces, and resting intervals shall not exceed 1/2 inch (13 mm) in height measured vertically to the highest point....
-
1003.2.12.2 Opening limitations
Open guards shall have balusters or ornamental patterns such that a 4-inch-diameter (102mm) sphere cannot pass through any opening up to a height of 34 inches (864mm)....
-
1.3.2 Focus Following NPRM Comments
This review identified four major issue areas for the MDE Advisory Committee to address, as follows: Transfer surface height and size Permitted obstructions to the transfer surface...
-
T502.4 Doorways with Steps on Over-the-Road Buses
The door opening clear width above a height of 48 inches (1220 mm) measured from the lowest step tread shall be permitted to taper so as to reduce in width to 18 inches (457 mm) minimum....
-
Tactile wayfinding
A Braille trail has a rope at waist height for a person with vision loss to follow and Braille labels for information....
-
1017.5 Tread Obstacles
Tread obstacles on trails, passing spaces, and resting intervals shall not exceed 1/2 inch (13 mm) in height measured vertically to the highest point....