The side wall grab bar shall be 42 inches (1067 mm) long minimum, located 12 inches (305 mm) maximum from the rear wall and extending 54 inches (1372 mm) minimum from the rear wall...
Search Results "Transfer System"
-
11B-604.5.1 Side wall
-
Staff Training
Finally, training staff to properly assist with transfers and lifts, and to use positioning aids correctly will minimize the chance of injury for both patients and staff....
-
Cells with Communication Features: ADA Standard Section 232.2.2
Section 232.2.2 covers scoping requirements in the current ADA Standards for cells with communication features.
-
1008.4.2 Clear Floor or Ground Space
Where play components include a seat or entry point, designs that provide for an unobstructed transfer from a wheelchair or other mobility device are recommended....
-
11B-1008.4.2 Clear floor or ground space
Where play components include a seat or entry point, designs that provide for an unobstructed transfer from a wheelchair or other mobility device are recommended....
-
11B-1008.4.2 Clear floor or ground space
Where play components include a seat or entry point, designs that provide for an unobstructed transfer from a wheelchair or other mobility device are recommended....
-
11B-232.2.2 Cells with communication features
At least 2 percent, but no fewer than one, of the total number of general holding cells and general housing cells equipped with audible emergency alarm systems and permanently installed...
-
11B-232.2.2 Cells with communication features
At least 2 percent, but no fewer than one, of the total number of general holding cells and general housing cells equipped with audible emergency alarm systems and permanently installed...
-
Height – M301.2.1 & M302.2.1
Height – M301.2.1 & M302.2.1 The subcommittee discussed the increments for adjustability and decided that infinite adjustability is the appropriate standard as both electronic...
-
F234.3 Minimum Number
Amusement rides shall provide at least one wheelchair space complying with 1002.4, or at least one amusement ride seat designed for transfer complying with 1002.5, or at least one transfer...
-
234.3 Minimum Number
Amusement rides shall provide at least one wheelchair space complying with 1002.4, or at least one amusement ride seat designed for transfer complying with 1002.5, or at least one transfer...
-
234.3 Minimum Number
Amusement rides shall provide at least one wheelchair space complying with 1002.4, or at least one amusement ride seat designed for transfer complying with 1002.5, or at least one transfer...
-
205 Operable Parts
controls) shall comply with 4.27. 4.27.3 Exception: These requirements do not apply where the use of special equipment dictates otherwise or where electrical and communications systems...
-
706.6 Peak Clipping Level
Peak clipping shall not exceed 18 dB of clipping relative to the peaks of speech. [ECTCR UFAS 4.33.7]
-
708.3 Handsets
Handset cords, if provided, shall be 29 inches (735 mm) long minimum.
-
§382.83 Through what mechanisms do carriers make seating accommodations?
[See subsections ...]
-
11B-706.6 Peak clipping level
Peak clipping shall not exceed 18 dB of clipping relative to the peaks of speech.
-
382.83 Through what mechanisms do carriers make seating accommodations?
382.83 Through what mechanisms do carriers make seating accommodations? ETA Editor's Note This section has no content in the original document.
-
11B-708.3 Handsets
Handset cords, if provided, shall be 29 inches (737 mm) long minimum.
-
708.3 Handsets
Handset cords, if provided, shall be 29 inches (735 mm) long minimum.
-
706.6 Peak Clipping Level
Peak clipping shall not exceed 18 dB of clipping relative to the peaks of speech.
-
Requirements to Remember for: Light Rail Projects
[See subsections ...]
-
706.6 Peak Clipping Level
706.6 Peak Clipping Level. Peak clipping shall not exceed 18 dB of clipping relative to the peaks of speech.
-
Sec. 12143. Paratransit as a complement to fixed route service. [Section 223]
[See subsections ...]