Key requirements apply to clear floor area, reach limits, knee and toe clearances and maneuvering clearances....
Search Results "Clearance in Base"
-
Executive Summary
-
Issue 23: Should design guidance for persons with low vision be prescriptive or performance based?
Comment by Marsha Mazz: I don’t know where we’re going with this because as we’ve said, time and time again, the issues of concern to this group here are not addressed by the...
-
Figure 608.2.3 Alternate Roll-In Type Shower Compartment Size and Clearance – Drawing from the U.S. Access Board
-
Figure 608.2.2 Standard Roll-In Type Shower Compartment Size and Clearance – Drawing from the U.S. Access Board
-
Rockwood Manufacturing Company 215 Tapered Door Pull 16"
Options: • Use Y prefix (Y215) when ordering pulls with base plates, Y plate diameter is 1-1⁄16"; recommended for use on glass or wood doors....
-
Rockwood Manufacturing Company 215L Tapered Door Pull 28"
Options: • Use Y prefix (Y215) when ordering pulls with base plates, Y plate diameter is 1-1⁄16"; recommended for use on glass or wood doors....
-
This is a great unit but it's not "recessed", it's semi-recessed.
unit next to the accessible lavatory or other required clear space and don't allow room for the projection, it may interfere with the minimum required clear floor space, door maneuvering clearance...
-
Pilot Rock: Picnic Table ADA Compliance Comparison
The ADA Guidelines define a "clearance box" that must fit under the table to be accessible....
-
1011.2.1 Size and Location
The size of the clear ground space is based on the dimensions for maneuvering clearance at clear floor or ground spaces that are confined on all or part of three sides in 305.7 of the Architectural...
-
Dome Size: ADA Standard Section 705.1.1
Truncated domes in a detectable warning surface shall have a base diameter of 0.9 inch (23 mm) minimum and 1.4 inches (36 mm) maximum, a top diameter of 50 percent of the base diameter minimum...
-
Notes
In mammography, the presence of the base support for the physical stability and operation of the equipment falls into this category....
-
11B-813.2.9 Overlap
Required clear floor spaces, clearance at fixtures, and turning space shall be permitted to overlap....
-
11B-603.2.2 Overlap
Required clear floor spaces, clearance at fixtures, and turning space shall be permitted to overlap....
-
11B-813.2.9 Overlap
Required clear floor spaces, clearance at fixtures, and turning space shall be permitted to overlap....
-
11B-603.2.2 Overlap
Required clear floor spaces, clearance at fixtures, and turning space shall be permitted to overlap....
-
Turning Space: ADA Standard Section 809.2.2
It is generally acceptable to use required clearances to provide wheelchair turning space....
-
NYC Board of Elections: Video 3 - Accessibility Clerk Responsibilities
-
ACCESS AISLE
[DSA-AC] An accessible space adjacent to or between vehicle spaces that provides clearances in compliance with this code....
-
Figure 604.3.2 (Exception) Overlap of Water Closet Clearance in Residential Dwelling Units – Drawing from the U.S. Access Board
-
Polling place violations that can be remediated with temporary measures
Building Entrance: The pull side of the entrance door does not provide at least 18 inches clearance to the side of the latch (1991 ADA Stds 4.13.6, Fig. 25; 2010 ADA Stds 404.2.4)...
-
11B-306.1 General
Clearances are measured in relation to the usable clear floor space, not necessarily to the vertical support for an element....
-
11B-306.1 General
Clearances are measured in relation to the usable clear floor space, not necessarily to the vertical support for an element....
-
TTYs: ADA Standard Section 217.4
Section 217.4 covers scoping requirements in the current ADA Standards for TTYs.
-
11B-705.1.1.1 Dome size
Truncated domes in a detectable warning surface shall have a base diameter of 0.9 inch (22.9 mm) minimum and 0.92 inch (23.4 mm) maximum, a top diameter of 0.45 inch (11.4 mm) minimum and...
