An in-tub seat or a seat at the head end of the tub shall be provided as shown in Fig. 33 and 34. The structural strength of seats and their attachments shall comply with 4.26.3....
Search Results "Head Height"
Filters
Commonly Searched Documents
-
4.20.3 SEAT
-
11B-608.3 Grab bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor....
-
11B-225.2.3 Library book stacks
ETA Editor's Note The ADA Advisory identifies library shelving as self-service shelving, which does not have a height limitation....
-
SECTION 202 DEFINITIONS
ETA Editor's Note Where ADA definitions for specific terms differ notably from CBC, the ADA definition is inserted below the CBC definition and identified by green text and headed...
-
Master Lock Mainstream Series ADA Keyed Locks Demonstration Video
student training video demonstrated how to open the Master Lock 1636MKADA and 1637MKADA Built-In Combination Locks using the student key with the Master Lock 1710-43959 ADA Compliant Key Head...
-
4.34.5.4(2) Seat
An in-tub seat or a seat at the head end of the tub shall be provided as shown in Fig. 33 and 34. The structural strength of seats and their attachments shall comply with 4.26.3....
-
4.34.5.4(5) Shower unit
A shower spray unit with a hose at least 60 in (1525 mm) long that can be used as a fixed shower head or as a hand-held shower shall be provided....
-
For EV with the charging port at rear of the vehicle, can EV be assumed to be able to back in the parking space for easy access to the charger at the head location?
RESPONSE: This practice is not regulated by the CBC Chapter 11B accessibility provisions. DSA is not aware of any restrictions on this practice.
-
Station 1-Physical Characteristics
Height-measured from the ground to the highest point on the device or vehicle or the top of the user's head, whichever is higher....
-
604.7 Open Type Toilet Paper Dispenser Height
-
902.3 Baby Changing Table Work Surface Height
-
American Standard Lexlie Pull-Down Kitchen Faucet 8471.301
The innovative Dock-Tite spray-head docking system and Re-Trax spray head retraction system makes operating the spray head easy and keeps it secured in place while not in use....
-
Character Spacing: ADA Standard Section 703.5.8
Spacing between individual characters shall be 10 percent minimum and 35 percent maximum of character height....
-
11B-703.5.8 Character spacing
Spacing between individual characters shall be 10 percent minimum and 35 percent maximum of character height....
-
Protruding Objects
There must be at least 80 inches clear height above the pedestrian route....
-
1009.5.1 Transfer Platform
A transfer platform shall be provided at the head of each transfer system....
-
Pilot Rock N-20 Series Charcoal Grill
Video showing adjustable heights of Pilot Rock N-20 Series Charcoal Grill. ...
-
A4.30.1 General
Many people with disabilities have limitations in movement of their heads and reduced peripheral vision....
-
Single Occupant Structures: ADA Standard Section 203.6
Section 203.6 covers scoping requirements of general exceptions for single occupant structures in the most current ADA Standards.
-
11B-203.6 Single occupant structures
Single occupant structures accessed only by passageways below grade or elevated above standard curb height, including but not limited to, toll booths that are accessed only by underground...
-
Hager Companies Door Protection Plate 220S
Door Protection Plate 220S 0.062" gauge with no bevel Materials: - Aluminum, brass, bronze, stainless steel Options: - Self-adhesive tape available on all plates - Spanner head...
-
Hager Companies Door Protection Plate 214S
Door Protection Plate 214S 0.125" gauge with 4-sided bevel Materials: - Plastic Laminate NFPA Notes: - Self-adhesive tape available on all plates - Spanner head screws...
-
11B-1009.5.1 Transfer platform
A transfer platform shall be provided at the head of each transfer system....
-
11B-411.2.2.1 Visible identification
The characters on the fixture shall be upper case with a height of 4 inches (102 mm) minimum complying with Sections 11B-703.5.1, 11B-703.5.3, 11B-703.5.4, 11B-703.5.7 and 11B-703.5.8....
