Transfer supports shall have a cross section complying with 305.2.4.1 or 305.2.4.2.
Search Results "Equipment Room"
-
M305.2.4 Cross Section
-
M305.2.3 Height
During use, the tops of transfer support gripping surfaces shall be 6 inches (150 mm) minimum and 19 inches (485 mm) maximum higher than the top of the associated uncompressed...
-
M305.2.6 Gripping Surface
Transfer support gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides. The bottoms of transfer support gripping surfaces...
-
M305.2.6 Gripping Surfaces (Section-by-Section Analysis)
The proposed rule did not provide any specific requirements regarding gripping surfaces on transfer supports. However, in the MDE NPRM preamble the Access Board repeatedly noted that...
-
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302 Description: Transfer supports may contain elements to provide structural support or prevent...
-
5.4.2 Transfer Support Length for M301 and M302
5.4.2 Transfer Support Length for M301 and M302 Description: Transfer support length applies to the gripping surface of the support, that portion of the support used to grasp or...
-
5.3 Transfer Sides
5.3 Transfer Sides.
-
5.3 Transfer Sides Recommendations
5.3 Transfer Sides Recommendations
-
M305.2.1 Location
Transfer supports shall be located within reach of the transfer surface and shall not obstruct transfer onto or off of the surface when in position.
-
11B-206.2.8 Employee work areas
Common use circulation paths located within employee work areas that are an integral component of work area equipment shall not be required to comply with Section 11B-402....
-
11B-206.2.8 Employee work areas
Common use circulation paths located within employee work areas that are an integral component of work area equipment shall not be required to comply with Section 11B-402....
-
Bench: ADA Standard Section 612.2
Section 612.2 covers the current ADA Standards for benches in saunas and steam rooms.
-
General description of monetized benefits for water closet clearance in single-user toilet rooms—in-swinging doors (Req. # 32)
The expert benefits panel estimated that single-user toilet rooms with in-swinging doors are used less frequently on average—about once every 20 visits to a facility with such a toilet room...
-
General description of monetized benefits for water closet clearance in single-user toilet rooms—in-swinging doors (Req. # 32)
The expert benefits panel estimated that single-user toilet rooms with in-swinging doors are used less frequently on average—about once every 20 visits to a facility with such a toilet room...
-
Harris Communications Inc. ADA Compliant Guest Room Kit 500A Hard Case
This kit is for a room in a hotel, hospital or nursing home. Save by purchasing this kit!...
-
11B-224.1 General
Hotels, motels, inns, resorts and similar transient lodging facilities shall provide guest rooms in accordance with Sections 11B-224.1 through 11B-224.6....
-
The Dwarf Athletic Association of America
Who We Are Founded in 1985, the Dwarf Athletic Association of America is a non-profit organization that provides athletic opportunities for people of short stature. The...
-
11B-612.2 Bench
Where seating is provided in saunas and steam rooms, at least one bench shall comply with Section 11B-903....
-
11B-612.2 Bench
Where seating is provided in saunas and steam rooms, at least one bench shall comply with Section 11B-903....
-
Tips for Presenters
To ensure access for attendees with electrical sensitivities, turn off non-essential computers, projectors, microphones, and other electronic equipment when not in use....
-
M302.2.3 Size
Transfer surfaces shall be 21 inches (610 mm) wide minimum and 17 inches (430 mm) deep minimum. The size of transfer surfaces shall be measured from center points of their opposing...
-
M302.3.2 Leg Supports
Where stirrups are provided, leg supports shall also be provided and comply with M305.4.
-
M302.3 Supports
Transfer supports, leg supports and reclining surfaces shall comply with M302.3.
