EXCEPTION: Within employee work areas, clearances on common use circulation paths shall be permitted to be decreased by work area equipment provided that the decrease is essential to the...
Search Results "Equipment Room"
-
403.5 Clearances
-
403.5 Clearances
EXCEPTION: Within employee work areas, clearances on common use circulation paths shall be permitted to be decreased by work area equipment provided that the decrease is essential to the...
-
11B-224.1 General
Hotels, motels, inns, resorts and similar transient lodging facilities shall provide guest rooms in accordance with Sections 11B-224.1 through 11B-224.6....
-
The Dwarf Athletic Association of America
Who We Are Founded in 1985, the Dwarf Athletic Association of America is a non-profit organization that provides athletic opportunities for people of short stature. The...
-
M305.2.1 Location
Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the...
-
M305.2.4 Cross Section
Transfer supports shall have a cross section complying with 305.2.4.1 or 305.2.4.2.
-
M305.2.3 Height
During use, the tops of transfer support gripping surfaces shall be 6 inches (150 mm) minimum and 19 inches (485 mm) maximum higher than the top of the associated uncompressed...
-
M305.2.6 Gripping Surface
Transfer support gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides. The bottoms of transfer support gripping surfaces...
-
M305.2.6 Gripping Surfaces (Section-by-Section Analysis)
The proposed rule did not provide any specific requirements regarding gripping surfaces on transfer supports. However, in the MDE NPRM preamble the Access Board repeatedly noted that...
-
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302 Description: Transfer supports may contain elements to provide structural support or prevent...
-
5.4.2 Transfer Support Length for M301 and M302
5.4.2 Transfer Support Length for M301 and M302 Description: Transfer support length applies to the gripping surface of the support, that portion of the support used to grasp or...
-
5.3 Transfer Sides
5.3 Transfer Sides.
-
5.3 Transfer Sides Recommendations
5.3 Transfer Sides Recommendations
-
M305.2.1 Location
Transfer supports shall be located within reach of the transfer surface and shall not obstruct transfer onto or off of the surface when in position.
-
11B-612.2 Bench
Where seating is provided in saunas and steam rooms, at least one bench shall comply with Section 11B-903....
-
11B-612.2 Bench
Where seating is provided in saunas and steam rooms, at least one bench shall comply with Section 11B-903....
-
11B-206.2.8 Employee work areas
Common use circulation paths located within employee work areas that are an integral component of work area equipment shall not be required to comply with Section 11B-402....
-
11B-206.2.8 Employee work areas
Common use circulation paths located within employee work areas that are an integral component of work area equipment shall not be required to comply with Section 11B-402....
-
Tips for Presenters
To ensure access for attendees with electrical sensitivities, turn off non-essential computers, projectors, microphones, and other electronic equipment when not in use....
-
224.6 Housing at a Place of Education
Housing at a place of education shall comply with the provisions applicable to transient lodging, including, but not limited to, the requirements for transient lodging guest rooms in sections...
-
G. Door Hardware
Is the door hardware (levers, pulls, panic bars, etc.) on all entry doors to accessible guestrooms and other passage doors within the room usable with one hand, without tight grasping, pinching...
-
Medical Care Facilities: ADA Standard Section 232.4
Section 232.4 covers scoping requirements in the current ADA Standards for medical care facilities.
-
11B-809.10.6 Showers
Showers required by Section 11B-809.10 shall comply with this section.
