Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
Search Results "Concrete Surface"
Commonly Searched Documents
-
505.7.1 Circular Cross Section
-
M301.2.1, M302.2.1 Transfer Height
measured from the floor to the top of the transfer surface...
- Bobrick Charting Station/Shelf B-7816
-
Transfer Surface Size – M301.2.2 Supine, Prone, or Side-Lying Position
Transfer Surface Size – M301.2.2 Supine, Prone, or Side-Lying Position The issues were discussed and decided in the full committee meeting as follows: depth of 17 inches minimum and width...
-
Technical Memorandum TM 2013-14 Dining Surfaces
dining surfaces based on TAS 201.1....
-
Triax 2000
A large tripod that can be raised to a fall height above the highest play surface on a playground. ...
-
11B-240.1 General
In existing play areas, where play components are relocated for the purposes of creating safe use zones and the ground surface is not altered or extended for more than one use zone, the...
-
11B-240.1 General
In existing play areas, where play components are relocated for the purposes of creating safe use zones and the ground surface is not altered or extended for more than one use zone, the...
-
11B-240.1 General
In existing play areas, where play components are relocated for the purposes of creating safe use zones and the ground surface is not altered or extended for more than one use zone, the...
- Steelcase Ology Series Height-Adjustable Table
-
5.2.1.1 Transfer Surface Width Recommendations for M301
5.2.1.1 Transfer Surface Width Recommendations for M301 The Committee recommends a transfer surface of 28 inches minimum width for equipment used by patients in a supine, side-lying,...
- GE® 30" Drop-In Electric Range JDS28DFWW
-
Stairways [§504]
Stairways [§504] Requirements for stairways address treads and risers, surfaces, nosings, and handrails....
-
402.2 Components
Accessible routes shall consist of one or more of the following components: walking surfaces with a running slope not steeper than 1:20, doorways, ramps, curb ramps excluding the flared...
-
5.4.4.2 Transfer Support Distance from Transfer Surface for Imaging Equipment
5.4.4.2 Transfer Support Distance from Transfer Surface for Imaging Equipment. Supports (transfer or positioning) should be located 1 ½ inches maximum from the transfer surface....
-
4.6.5 Slope
When the surface is not paved or is not elevated above the natural ground, slopes not steeper than 1:33 (3 percent) shall be permitted where necessary for drainage. ...
-
1017.4 Passing Spaces
tread width on trails or passing spaces at shorter intervals where the trail is heavily used or where the trail is a boardwalk or otherwise not at the same level as the adjoining ground surface...
- GE® 27" Drop-In Electric Range JM250DFBB
-
Elevator Car Requirements [§407.4.2 – §407.4.5]
Elevator Car Requirements [§407.4.2 – §407.4.5] Other requirements for elevator cars include: compliant floor surfaces a maximum 1¼” horizontal clearance between car...
-
11B-1009.2.3 Clear deck space
On the side of the seat opposite the water, a clear deck space shall be provided parallel with the seat. The space shall be 36 inches (914 mm) wide minimum and shall extend forward...
-
1009.2.3 Clear Deck Space
On the side of the seat opposite the water, a clear deck space shall be provided parallel with the seat. The space shall be 36 inches (915 mm) wide minimum and shall extend forward...
-
1016.7 Slopes
The slopes of outdoor recreation access routes shall comply with 1016.7.
-
1009.2.3 Clear Deck Space
On the side of the seat opposite the water, a clear deck space shall be provided parallel with the seat. The space shall be 36 inches (915 mm) wide minimum and shall extend forward...
-
Summary of Recommendations
Summary of Recommendations