[ADA Title III] §36.406(b) Standards for New Construction and Alterations; Scope of Coverage....
Search Results "Brand Standards"
Filters
Commonly Searched Documents
-
11B-201.1 Scope
-
INTRODUCTION
These changes include revised accessibility standards, called the 2010 Standards for Accessible Design (2010 Standards), which establish minimum criteria for accessibility in design and...
-
11B-202.3.1 Prohibited reduction in access
(c) If the 2010 Standards reduce the technical requirements or the number of required accessible elements below the number required by the 1991 Standards, the technical requirements or the...
-
Multiple Single-User Toilet Rooms
Where multiple single-user toilet rooms are clustered in a single location, fifty percent (50%), rather than the one hundred percent (100%) required by the 1991 Standards, are required to...
-
5.2.2.1 Transfer Surface Width Recommendations for M302
recommends 21 inches for the minimum width of the transfer surface of examination chairs and other equipment primarily used by patients in a seated position as described in its proposed standard...
-
B.3.iv - Who makes the determination that a product meets equivalent facilitation?
The vendor may assert that its product meets or exceeds the level of accessibility required by a particular standard through equivalent facilitation....
-
24.1 Q. What types of grab bars should the reinforcement be designed to accommodate and what types may be used if the builder elects to install grab bars in some units at the time of construction?
In determining what is an appropriate grab bar, builders are encouraged to look to the 1986 ANSI A117.1 standard, the standard cited in the Fair Housing Act....
-
§ 36.304(d)(2)(iii)
., elements for which there are neither technical nor scoping specifications in the 1991 Standards), and therefore those elements must be modified to the extent readily achievable to comply...
-
Alterations and Additions
This guide provides an introduction to the scoping requirements that form the basis for the Department of Justice’s 2010 ADA Standards and the Department of Transportation's ADA Standards...
-
11B-202.3.1 Prohibited reduction in access
(c) If the 2010 Standards reduce the technical requirements or the number of required accessible elements below the number required by the 1991 Standards, the technical requirements or the...
-
E202.7 Best Meets
Where ICT conforming to one or more requirements in the Revised 508 Standards is not commercially available, the agency shall procure the ICT that best meets the Revised 508 Standards consistent...
-
M101.1 Purpose
The proposed standards contain technical criteria for medical diagnostic equipment that is accessible to and usable by patients with disabilities....
-
11B-904.4.1 Parallel approach
[2010 ADA Standards] 904.4.1 Parallel Approach....
-
11B-604.4 Seats
[2010 ADA Standards] 604.4 Seats....
-
11B-502.5 Vertical clearance
[2010 ADA Standards] 502.5 Vertical Clearance....
-
Section 36.406(e) Housing at a Place of Education
standards....
-
Section 35.151(f) Housing at a place of education
standards....
-
R105.3 Undefined Terms
The meaning of terms not specifically defined in R105.5, the referenced standards, or regulations issued by Federal agencies that adopt this document as accessibility standards shall be...
-
Height: ADA Standard Section 1005.2.1
1003.2.12.2 of the International Building Code (2000 edition) or sections 1012.2 and 1012.3 of the International Building Code (2003 edition) (incorporated by reference, see “Referenced Standards...
-
11B-404.2.5 Thresholds
[2010 ADA Standards] EXCEPTION: Existing or altered thresholds ¾ inch (19 mm) high maximum that have a beveled edge on each side with a slope not steeper than 1:2 shall not be required...
-
11B-605.4 Flush controls
[2010 ADA Standards] 605.4 Flush Controls. Flush controls shall be hand operated or automatic. Hand operated flush controls shall comply with 309....
-
11B-903.3 Size
[2010 ADA Standards] 903.3 Size. Benches shall have seats that are 42 inches (1065 mm) long minimum and 20 inches (510 mm) deep minimum and 24 inches (610 mm) deep maximum....
-
Section 4.26.4
• Section 4.26.4 of the 1991 Standards requires handrail gripping surfaces to have edges with a minimum radius of 1/8 inch....
-
§ 36.304(d)(2) Safe harbor
Elements in existing facilities that are not altered after [insert effective date of final rule], and that comply with the 1991 Standards, are not required to be modified in order to comply...