As well as a 24 In. combination slide car/grab bar with stainless steel and chrome finish. The VS-100 hand-held shower includes a push button trickle feature for reducing water flow....
Search Results "Car Dimension"
Filters
Commonly Searched Documents
-
Speakman Versatile ADA Hand Shower System VS-1001-ADA-PC
-
Signals: ADA Standard Section 407.2.1.5
Section 407.2.1.5 covers the current ADA Standards for elevator call control signals.
-
409.2 Call Buttons
Call buttons shall be ¾ inch (19 mm) minimum in the smallest dimension and shall comply with 309....
-
3.1 GRAPHIC CONVENTIONS
Dimensions that are not marked "minimum" or "maximum" are absolute, unless otherwise indicated in the text or captions....
-
AccessRec GrassProtecta Slip Resistant Grass Reinforcement Mesh
GRASSPROTECTA® slip resistant is a cost effective solution for: Grass car parks Overflow grass car parks Light aircraft taxiways Equestrian surfaces...
-
304 Turning Space
Comments urged that the minimum dimensions for turning space be increased to better accommodate scooters and motorized wheelchairs....
-
Clearance Around Base (M301.4.2 and M302.4.2)
Comments are requested on the following questions regarding the proposed dimensions for clearance around the base of the equipment to allow the use of portable floor lifts: a) Are the...
-
Comments
Accessibility approaches that limited access to a single car (sometimes referred to in comments as the “cattle car” approach) were unacceptable and discriminatory, they said....
-
Seeger et al.
Both unoccupied and occupied dimensions of device width and length were measured as well as a set of other basic dimensions....
-
§ 38.175(a)
The design of cars shall be coordinated with the boarding platform design such that the horizontal gap between a car door at rest and the platform shall be no greater than 3 inches and the...
-
Question 15
What are appropriate scoping requirements for accessible golf cars?...
-
11B-409.2 Call buttons
Call buttons shall be ¾ inch (19.1 mm) minimum in the smallest dimension and shall comply with Section 11B-309 _|Operable Parts|_....
-
Technical Requirements
Are the specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.)....
-
Technical Requirements
The specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.). ...
-
11B-409.2 Call buttons
Call buttons shall be ¾ inch (19.1 mm) minimum in the smallest dimension and shall comply with Section 11B-309 _|Operable Parts|_....
-
12162(a)(4)(A)(i)
(i) if such single-level dining car was purchased after July 26, 1990, table service in such car shall be provided to a passenger who uses a wheelchair if...
-
11B-411.4.11.3 Duration
Floor destination characters shall be displayed upon elevator car arrival at the input floor and shall not extinguish until the elevator car arrives at the destination floor....
-
11B-411.4.11.3 Duration
Floor destination characters shall be displayed upon elevator car arrival at the input floor and shall not extinguish until the elevator car arrives at the destination floor....
-
11B-411.4.11.3 Duration
Floor destination characters shall be displayed upon elevator car arrival at the input floor and shall not extinguish until the elevator car arrives at the destination floor....
-
11B-608.2.2 Standard roll-in type shower compartments
Standard roll-in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
11B-608.2.2 Standard roll-in type shower compartments
Standard roll-in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
Clearance in Base (M301.4.1 and M302.4.1)
Comments are requested on the following questions regarding the proposed dimensions for clearance in the base of the equipment to allow the use of portable floor lifts: a) Are the proposed...
-
§382.133(e)(2)
(2) The maximum weight and dimensions (length, width, height) of the device to be used by an individual that can be accommodated in the aircraft cabin consistent with FAA safety requirements...
-
407.2.1.2 Size
Call buttons shall be ¾ inch (19 mm) minimum in the smallest dimension. EXCEPTION: Existing elevator call buttons shall not be required to comply with 407.2.1.2....
