., concrete, brick, flagstone) may have a maximum change in height from the interior landing of 1 inch (25.4 mm), provided a ramp with a maximum slope of 1:8 is permanently installed....
Search Results "Built-Up Curb Ramp"
Filters
Commonly Searched Documents
-
1132A.4, Item 4
-
11B-503.5 Vertical clearance
Vehicle pull-up spaces, access aisles serving them, and a vehicular route from an entrance to the passenger loading zone and from the passenger loading zone to a vehicular exit shall provide...
-
406.3 Sides of Curb Ramps
Where provided, curb ramp flares shall not be steeper than 1:10. Figure 406.3 Sides of Curb Ramps...
-
SafePath: Overview of Ramps and Reducers for ADA Compliance by SafePath Products
SafePath™ manufactures ramps, landings, seismic surface transitions, flooring reducers and other industrial and residential products for ADA (American's with Disability Act) and access code...
-
1015.3 Height
On ramps and ramped aisles, from the ramp surface at the guard....
-
§ 38.125(c)(1) Design load
Ramps or bridge plates 30 inches or longer shall support a load of 600 pounds, placed at the centroid of the ramp or bridge plate distributed over an area of 26 inches by 26 inches, with...
-
11B-503.5 Vertical clearance
Vehicle pull-up spaces, access aisles serving them, and a vehicular route from an entrance to the passenger drop-off and loading zone and from the passenger drop-off and loading zone to...
-
11B-503.4 Floor and ground surfaces
Vehicle pull-up spaces and access aisles serving them shall comply with Section 11B-302. Access aisles shall be at the same level as the vehicle pull-up space they serve....
-
Americans with Disabilities Act (ADA) Standards for Transportation Facilities
based on the Board's ADA Accessibility Guidelines (ADAAG) but include additional requirements concerning: Location of Accessible Routes (206.3) Detectable Warnings on Curb...
-
§ 38.159(c)(1) Design load
Ramps 30 inches (760 mm) or longer shall support a load of 600 pounds (2665 N), placed at the centroid of the ramp distributed over an area of 26 inches by 26 inches (660 mm by 660 mm),...
-
11B-805 Medical care and long-term care facilities
SECTION 11B-805 Medical care and long-term care facilities 11B-805.7 Built-in cabinets and work surfaces....
-
Portable ramp - greater than six inch step
[See subsections ...]
-
Figure 503.3 Passenger Loading Zone Access Aisle – Drawing from the U.S. Access Board
-
§ 38.125(c)(7) Stowage
A compartment, securement system, or other appropriate method shall be provided to ensure that stowed ramps or bridge plates, including portable ramps or bridge plates stowed in the passenger...
-
1015.2 Where required
Guards shall be located along open-sided walking surfaces, including mezzanines, equipment platforms, aisles, stairs, ramps and landings that are located more than 30 inches (762 mm) measured...
-
seca 664 Digital Wheelchair Scale with Wireless Transmission
High capacity and easy to mount ramp. With the scale’s load-bearing capacity of 800 lbs, weighing even heavy wheelchair patients is effortless with the seca 664....
-
T202 Accessible Means of Boarding and Alighting
These vehicles must also provide access to the roadway in the event passengers must be offloaded where there is no platform or curb....
-
R407.6.1 Slope
R407.6.1 Slope. Landing slopes shall be 2 percent maximum in any direction.
-
1013.3 Height
On ramps, from the ramp surface at the guard. Exceptions: 1. ...
-
Requirements to Remember for ADA Compliance in Construction Projects: Transportation Facilities
Access Board’s updated ADA (and ADAAG) guidelines but includes a few additional requirements concerning: Location of Accessible Routes (206.3) Detectable Warnings on Curb...
-
1013.2 Where required
Guards shall be located along open-sided walking surfaces, including mezzanines, equipment platforms, stairs, ramps and landings that are located more than 30 inches (762 mm) measured vertically...
-
1015.2 Where required
Guards shall be located along open-sided walking surfaces, including mezzanines, equipment platforms, aisles, stairs, ramps and landings that are located more than 30 inches (762 mm) measured...
-
F225 Storage
[See subsections ...]
-
902.4.2 Height
The tops of tables and counters shall be 26 inches (660 mm) minimum and 30 inches (760 mm) maximum above the finish floor or ground.
