Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
Search Results "Parallel Curb Ramp"
-
1131A.2 Changes greater than ½ inch
-
seca 676 r Digital Wheelchair Scale with Handrail and Integrated RS232 Interface
Two ramps included. Pre-TARE function with three memory cells....
-
4.34.3(2)(b) Reach Depth More Than 10 in
(b) Reach Depth More Than 10 in (255 mm). Where the reach depth to the operable parts of any control as measured from the vertical plane perpendicular to the edge of the unobstructed...
-
4.34.3(2)(a) Reach Depth Not More Than 10 in
(a) Reach Depth Not More Than 10 in (255 mm). Where the reach depth to the operable parts of all controls as measured from the vertical plane perpendicular to the edge of the...
-
Clear Floor Space [§309.2]
Clear Floor Space [§309.2] Clear floor space can be oriented for a side approach instead of a forward approach at most operable parts. Nominal centering of the space on operable...
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
502.3 Access Aisle
Exception: Access aisles are not required for on-street parallel parking....
-
11B-406.2.2 Sides of curb ramps
Where provided, curb ramp flares shall not be steeper than 1:10. FIGURE 11B-406.2.2 ‡‡ SIDES OF CURB RAMPS...
-
Cross Slope and Surfaces [4.8.6]
Ramp surfaces must comply with requirements for ground and floor surfaces and be "stable, firm, and slip-resistant." A specific level of slip-resistance is not mandated....
-
seca 684 r Digital Multifunctional Scale with Integrated RS232 Interface
Ramp seca 470 included. TARE, Auto-HOLD and damping function. Integrated transport castors allow for easy mobility....
-
5.9.2 Standing Supports on Ramped Entry Raised Platforms with Wheelchair Spaces
5.9.2 Standing Supports on Ramped Entry Raised Platforms with Wheelchair Spaces....
-
5.8.1.2.2 Single Ramped Entry - Edge Protection on the Platform and Platform Sides Recommendations
5.8.1.2.2 Single Ramped Entry - Edge Protection on the Platform and Platform Sides Recommendations The Committee recommends a two-inch high edge protection on the back of the platform...
-
Problem Three (Accessible Route)
Solution: Install a portable ramp....
-
EZ-ACCESS Transitions® Modular Entry Mat Video
Requires the Registered User plan or above. Login! -
Re: Husky 24" Line Generator Digital Laser Level
See Bill Hecker, AIA, Kirola vs City and County of San Francisco, Expert for DOJ, testimony with regards to Laser level lengths.
-
11B-505.9 Fittings
Handrails shall not rotate within their fittings.
-
505.9 Fittings
Handrails shall not rotate within their fittings.
-
4.8.4(4)
(4) If a doorway is located at a landing, then the area in front of the doorway shall comply with 4.13.6.
-
505.9 Fittings
Handrails shall not rotate within their fittings.
-
11B-505.9 Fittings
Handrails shall not rotate within their fittings.
-
§ 38.83(c)(6) Attachment
(6) Attachment—
-
11B-505.9 Fittings
Handrails shall not rotate within their fittings.
-
11B-405.7.1 Slope
Landings shall comply with Section 11B-302. Changes in level, slopes exceeding 1:48, and detectable warnings shall not be permitted. Exception: Reserved.
