• G-Max® fl ushing system, low consumption (1.6GPF/6.0LPF) • Universal Height • Two-piece design with high-profi le tank • Elongated front bowl and tank set, less seat...
Search Results "Seat Location"
-
TOTO® Drake Two-Piece Toilet, 1.6 GPF, Elongated Bowl
-
Sec.36.308(a)(3)
(3) The requirements of paragraph (a) of this section shall not be interpreted to exceed the standards for alterations in subpart D of this part.
-
Delta Toilet with FlushIQ Round Front C41903T-WH
electronics and mechanical parts Features ADA compliant chair height bowl to make sitting down and standing up easier 2 in. fully glazed trap-way Round-front bowl with slow-close seat...
-
Neo-Metro Urban Stainless Steel Toilet 8950-3-ADA-PFS
Toilet seats are sold seperately. ADA height is also avaliable....
-
Highest and Lowest Heights Obtained
The 5th percentile lowest and highest transfers attained were similar to the average WMD seat height (22.1 inch) for all protocols....
-
Transfer Protocols
to device positioning (if any), use of a transfer board, and surface(s) used for the leading hand (e.g. reaching to new surface) and trailing hand (e.g. left behind during move to new location...
-
Addendum G: Comparison of Transfer Abilities between Men and Women
The average wheelchair seat to floor height for men was 22.2 (±1.44) inches and the average height for women was 21.65 (±1.31) inches....
-
11B-216.2 Designations
Exception: Exterior signs that are not located at the door to the space they serve shall not be required to comply with Section 11B-703.2. ...
-
American Standard Right Width 1.28-1.6 gpf FloWise Right Height Elongated Flushometer Toilet
Elongated floor mount flushometer valve toilet, top spud, with seat High Efficiency, Low Consumption operates in the range of 1.28gpf to 1.6gpf (4.8Lpf to 6.0Lpf) Right HeightTM...
-
11B-206.2.4 Spaces and elements
In assembly areas with fixed seating required to comply with Section 11B-221, an accessible route shall not be required to serve fixed seating where wheelchair spaces required to be on an...
-
11B-206.2.4 Spaces and elements
In assembly areas with fixed seating required to comply with Section 11B-221, an accessible route shall not be required to serve fixed seating where wheelchair spaces required to be on an...
-
11B-206.2.4 Spaces and elements
In assembly areas with fixed seating required to comply with Section 11B-221, an accessible route shall not be required to serve fixed seating where wheelchair spaces required to be on an...
-
5.4.5 Transfer Support Position for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.5 Transfer Support Position for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
G. Chapter 6: Wheelchair Spaces and Securement Systems
Chapter 6 in the 2016 Non-Rail Vehicle Guidelines establishes technical requirements for wheelchair spaces, wheelchair securement systems, and seat belts and shoulder belts provided for...
-
Transfer Supports Location and Configuration M301.3 and M302.3
Transfer Supports Location and Configuration M301.3 and M302.3 Location of the transfer supports shall be a minimum of 6 inches to a maximum of 19 inches from the top of the transfer...
-
I. BACKGROUND AND JURISDICTION
for the Eastern District of Michigan, a component of the United States Department of Justice (“United States”), alleging that Joe Louis Arena, a sports and entertainment stadium venue located...
-
M303.2.3.1 Front or Rear Entry
Where wheelchair space entry and exit is provided at only one end (front or rear) the wheelchair space shall be 48 inches (1220 mm) deep minimum.
-
ABA CHAPTER 9: BUILT-IN ELEMENTS
[See subsections ...]
-
M303.2.3.3 Side Entry
Where wheelchair space entry is only from the side, the wheelchair space shall be 60 inches (1525 mm) deep minimum.
-
M303.2.3.2 Pass Through Entry
Where wheelchair space entry and exit permits pass through from one end to the other, the wheelchair space shall be 40 inches deep (1015 mm) minimum.
-
Chapter 9: Built-In Elements
Chapter 9 covers built-in elements, including dining surfaces and work surfaces (902), benches (903), and sales and service counters (904). Changes made to this section...
-
CHAPTER 9: BUILT-IN ELEMENTS
CHAPTER 9: BUILT-IN ELEMENTS
-
DIVISION 9: BUILT-IN ELEMENTS
[See subsections ...]
-
DIVISION 9: BUILT-IN ELEMENTS
[See subsections ...]
