its depth spanned the examination surface’s width, and was located near the center point of the diagnostic equipment surface....
Search Results "Kitchen Work Surface"
Filters
Commonly Searched Documents
-
(1) Transfer Surface Location for Diagnostic Equipment Used in the Supine, Prone, or Side-lying Position
-
11B-205.1 General
Where two or more outlets are provided in a kitchen above a length of counter top that is uninterrupted by a sink or appliance, one outlet shall not be required to comply with 309....
-
KICK PLATE
An abrasion-resistant plate affixed to the bottom portion of a door to prevent a trap condition and protect its surface. Advisory Definition of KICK PLATE. ...
-
KICK PLATE
An abrasion-resistant plate affixed to the bottom portion of a door to prevent a trap condition and protect its surface. Advisory Definition of KICK PLATE....
-
KICK PLATE
An abrasion-resistant plate affixed to the bottom portion of a door to prevent a trap condition and protect its surface. Advisory Definition of KICK PLATE....
-
6. Transfer Surface Height
Transfer Surface Height 6.3 Diagnostic Imaging Equipment Refer to the Rationale found in Section 5.3 for M301.2.1 and to Section 4.3....
-
Storage: ADA Standard Section 225
Section 225 covers scoping requirements in the current ADA Standards for storage.
-
11B-225 Storage
[See subsections ...]
-
Study Questions
Study Questions The purpose of this study was to evaluate a variety of playground surfaces, their ability to meet accessibility requirement, their costs upon initial installation and...
-
Visible Alarms
These commenters also raised concerns that all employee work areas within existing buildings and facilities must be equipped with accessibility features....
-
405.9.1 Extended Floor or Ground Surface
405.9.1 Extended Floor or Ground Surface....
-
5.2.2.2 Transfer Surface Depth Recommendation for M302
5.2.2.2 Transfer Surface Depth Recommendation for M302 The Committee recommends a minimum depth requirement of 17 inches for equipment used by patients in seated positions....
-
405.9.1 Extended Floor or Ground Surface
The floor or ground surface of the ramp run or landing shall extend 12 inches (305 mm) minimum beyond the inside face of a handrail complying with 505....
-
Eco-Grip Flooring Video 6 of 8 Epoxy Mastic Application
Eco-Grip Flooring Epoxy Mastic Application
-
Inpro Corporation JointMaster® 925 Fire Barrier System Expansion Joint Systems
The 925 Fire Barrier system meets the “Hose System Test” for masonry and concrete walls. Features & Benefits Economical system for joint widths up to 3"...
-
Inpro Corporation JointMaster® 441 Series-Recessed Mount Expansion Joint
The 441 is a highly modifiable system with varying thicknesses of aluminum or stainless steel cover plates that can meet many project’s loading requirements. Features &...
-
Inpro Corporation JointMaster® 103 Series-VCT Expansion Joint Systems
The unique frame design of the 103 creates a smooth transition over joint for wheeled equipment. Features & Benefits Seals absorb limited serviceable seismic...
-
Inpro Corporation JointMaster® 787 Series Floor Expansion Joint Covers
The integral, high durometer seal of the 787 deters water from entering the system and acts as a noise dampening device. Features & Benefits Seismic capable system...
-
Inpro Corporation JointMaster® 300 Series Recessed Mount Floor Expansion Joint Covers
The patented "no-bump" design makes this product ADA compliant. Features & Benefits Patented "no-bump" configuration ADA compliant Gasketed to...
-
Inpro Corporation JointMaster® 101 Series Floor Expansion Joint Covers
The 101 Series is adaptable to many flooring finishes, including ceramic tile, marble, stone, vinyl, tile and carpet. Features & Benefits: Dual durometer seal...
-
Cross Section: ADA Standard Section 505.7
Section 505.7 covers the current ADA Standards for the cross section of handrail gripping surfaces.
-
405.9.1 Extended Floor or Ground Surface
The floor or ground surface of the ramp run or landing shall extend 12 inches (305 mm) minimum beyond the inside face of a handrail complying with 505....
-
11B-403.3 Slope
The running slope of walking surfaces shall not be steeper than 1:20. The cross slope of walking surfaces shall not be steeper than 1:48....
-
11B-403.3 Slope
The running slope of walking surfaces shall not be steeper than 1:20. The cross slope of walking surfaces shall not be steeper than 1:48....
