Public telephones serving the area of alteration • Exterior or interior signs along the path of travel • Accessible route components • Walking surfaces dimensions • Running slope...
Search Results "Counter Slope"
Filters
Commonly Searched Documents
-
4. COMMON PATH OF TRAVEL ITEMS
-
Transition Plates
Transition Plates Transition plates are sloping pedestrian walking surfaces located at the end of a gangway....
-
Maneuvering Space Where Ramps are Provided
The space must have a slope no steeper than 1:48 in all directions. ...
-
Transition Plates
Transition Plates Transition plates are sloping pedestrian walking surfaces located at the end of a gangway....
-
Mirror Height
The ANSI A117.1‒2003 standard contains a new requirement that specifies a height of 35 inches maximum for accessible mirrors not located above a lavatory or counter top....
-
Inventory Control Devices
This clearance is often useful at exterior doors without latches in countering the force of closers and wind resistance. When doors are automated, maneuvering space is not required....
-
505.1 General
Handrails are not required on walking surfaces with running slopes less than 1:20....
-
505.1 General
Handrails are not required on walking surfaces with running slopes less than 1:20....
-
704.11.1 Parapet construction
Where the roof slopes toward a parapet at a slope greater than two units vertical in 12 units horizontal (16.7-percent slope), the parapet shall extend to the same height as any portion...
-
11B-505.1 General
Handrails are not required on walking surfaces with running slopes less than 1:20....
-
1018.1 General
The technical requirements address connections (1018.2); surface (1018.3); clear width (1018.4); obstacles (1018.5); openings (1018.6); slopes, including running slope (1018.7.1) and cross...
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
1131A.1 Changes in level not exceeding ½ inch
When changes in level do occur, they shall be beveled with a slope no greater than 1 unit vertical in 2 units horizontal (50-percent slope)....
-
Beveled: ADA Standard Section 303.3
Section 303.3 covers the current ADA Standards for beveled level changes.
-
804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware....
-
804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware....
-
505.1 General
Handrails are not required on walking surfaces with running slopes less than 1:20....
-
Rise
The maximum length of a run is determined by the rise (30 inches maximum) and the slope: Max. Rise Slope Max. Length Max. Rise Slope Max....
-
1017.10 Trailhead Signs
requires trail information signs at trailheads to include information on the length of the trail or trail segment; surface type; typical and minimum tread width; typical and maximum running slope...
-
11B-411.2.1.3.4 Position
The face of individual elements or group of individual elements that are operated by user input shall slope away from the user at 15 to 25 degrees from the vertical plane. ...
-
1134A.6, Item 5
When a threshold is used, it shall be a maximum of 2 inches (50.8 mm) in height and have a beveled or sloped angle not exceeding 1 unit vertical in 2 units horizontal (26.6 degrees from...
-
Transits and construction lasers
Transits and construction lasers are useful for setting or measuring overall elevation points to determine a total slope....
-
Original research for ANSI A117.1 (1957 - 1961)
Both slope and cross slope were measured. These guidelines for measurement were deleted from later versions of the standard....
-
1134A.6, Item 5
When a threshold is used, it shall be a maximum of 2 inches (50.8 mm) in height and have a beveled or sloped angle not exceeding 1 unit vertical in 2 units horizontal (26.6 degrees from...