Tent pads and platforms shall have a surface that is firm and stable and is designed to allow use of tent stakes and other tent securing devices. Exception....
Search Results "Surface"
Filters
Commonly Searched Documents
-
4.3.4 Tent Pad or Platform Surface
-
810.2.1 Surface
810.2.1 Surface. Bus stop boarding and alighting areas shall have a firm, stable surface....
-
1002.4.1 Floor or Ground Surface
The floor or ground surface of wheelchair spaces shall be stable and firm....
-
1002.4.1 Floor or Ground Surface
The floor or ground surface of wheelchair spaces shall be stable and firm....
-
4.4.6 Surface
The surface of the clear floor or ground space for benches shall be firm and stable. The type of surface should be appropriate to the setting and level of development....
-
Surface
The top layer of a trail.
-
Surface
Surface—The top layer of ground on a recreation site, outdoor recreation access route, trail, or beach access route Firm. A surface that resists deformation by indentations....
-
802.1.1 Floor or Ground Surface
The floor or ground surface of wheelchair spaces shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
802.1.1 Floor or Ground Surface
The floor or ground surface of wheelchair spaces shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
Surface, Slope, and Openings [1011.2.2, 1011.2.3, and 1011.2.4]
The surface of the clear ground space must be firm and stable. Additional information on firm and stable surfaces is provided in the trails section of this guide....
-
4.3.6 Surface Textures
The surface of an accessible route shall comply with 4.5....
-
4.3.6 SURFACE TEXTURES
The surface of an accessible route shall comply with 4.5....
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
Acceptable Trail Surfacing Requirements
Trail surfaces are currently considered accessible only if the surfacing material is firm, stable, and slip-resistant and the trail has the engineered attributes of adequate width, moderately...
-
b. Transfer Surface Location
The MDE NPRM proposed the same location and transfer sides of the transfer surface for diagnostic equipment used by patients in the supine, prone, or side-lying position (M301) and diagnostic...
-
Bonded Impact/cushioning Surfaces
Bonded Impact/cushioning Surfaces Eight different surface test specimens were formed with surface dimensions of 1.2m x 1.2m with a depth of 0.3m (48”x48”x 12”) in Madison WI (Figure 1...
-
1018.3 Surface
The surface of beach access routes and resting intervals shall be firm and stable....
-
1018.3 Surface
The surface of beach access routes and resting intervals shall be firm and stable....
-
810.2.1 Surface
Bus stop boarding and alighting areas shall have a firm, stable surface....
-
810.2.1 Surface
Bus stop boarding and alighting areas shall have a firm, stable surface....
-
1018.3 Surface
This section requires the surface of beach access routes and resting intervals to be firm and stable....
-
Firmness or Firm Surface
Firmness or Firm Surface. A firm surface resists deformation by either indentations or particles moving on its surface (2010 ADA Standards for Accessible Design, Advisory 302.1). ...