Transfer supports shall be provided for use with the transfer sides required by M301.2.3 and shall comply with M305.2.
Search Results "Imaging Equipment"
-
M301.3.1 Transfer Supports
-
M301.3 Supports
Transfer supports, stirrups, and reclining surfaces shall comply with M301.3.
-
M305.2.3 Height (Section-by-Section Analysis)
The manufacturer opposing the proposed range raised concerns with its ability to attain a 19-inch height on its diagnostic equipment....
-
11B-805.4.2 Equipment
Clear space complying with Section 11B-305.2 shall be provided as required for specific equipment....
-
11B-805.4.2 Equipment
Clear space complying with Section 11B-305.2 shall be provided as required for specific equipment....
-
5.4.8 Transfer Support Gripping Surface Hazard for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.8 Transfer Support Gripping Surface Hazard for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
5.7.1 Lift Compatibility Clearance in Base for M301
maneuver far enough over the equipment to safely lower and raise the patient onto and off examination surfaces....
-
§ 1194.21(e)
(e) When bitmap images are used to identify controls, status indicators, or other programmatic elements, the meaning assigned to those images shall be consistent throughout an application...
-
M301.2.4 Unobstructed Transfer
Each transfer surface shall provide two unobstructed sides for patient transfer. EXCEPTIONS: 1. Obstructions no more than 3 inches (75 mm) deep shall be permitted to extend beyond...
-
M301.2.3 Transfer Sides
The transfer surface shall be located to provide options to transfer from a mobility device onto one short side (depth) and one long side (width) of the surface. Each transfer side...
-
M301.4 Lift Compatibility (Section-by-Section Analysis)
This provision clearly states that diagnostic equipment shall comply with clearance in base or clearance around base....
-
M305.2.8 Fittings (Section-by-Section Analysis)
A different manufacturer stated that its seated diagnostic equipment uses armrests as transfer supports, which can be pushed back toward the rear of the equipment to allow entry....
-
5.4.1 Transfer Support Location for M301 and M302
, it is recommended that supports be provided on each side of the transfer surface that is 15 inches deep minimum for patients to maintain position after they have transferred onto the equipment...
-
d. Unobstructed Transfer
As explained in the MDE NPRM preamble, the unobstructed access requirement was to ensure that armrests, side rails, stirrups, or other equipment parts attached to the diagnostic equipment...
-
M305.2.7 Clearance (Section-by-Section Analysis)
Specifically, the Access Board sought input from the public in question 22, on whether transfer supports on diagnostic equipment could provide 1½ inches minimum clearance around the gripping...
-
EXHIBIT 1 JEFFERSON OUTPATIENT IMAGING ADA POLICY AND PROCEDURE
In accordance with Title III of the Americans with Disabilities Act (ADA), Jefferson Outpatient Imaging and Radiology (“Jefferson Outpatient”) does not discriminate on the basis of disability...
-
5.4.7 Transfer Support Gripping Surface Clearance Recommendation for M301 and M302
This clearance would allow the fingers and knuckles to clear adjacent equipment parts as they grip the support....
-
5.4.5 Transfer Support Position Recommendation for M301 and M302
It addresses angled supports or contoured portions of horizontal supports often provided for ergonomics or equipment design considerations....
-
M305.2.2.2 Side Transfer Supports
Where the width of an imaging bed is more than 24 inches (533 mm), transfer supports shall be permitted to be 12 inches (305 mm) long minimum....
-
M305.2.4 Cross Section (Section-by-Section Analysis)
The Access Board sought input in MDE NPRM preamble question 21, on whether the gripping surfaces of current transfer supports on different types of equipment meet the cross sectional dimensions...
-
M305.2.2 Length
The length of transfer supports shall comply with M305.2.2.1 or M305.2.2.2.
-
M301.2.1 Height
The height of the transfer surface during patient transfer shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum measured from the floor to the top of the transfer...
-
11B-236.1 General
At least one of each type of exercise machine and equipment shall comply with Section 11B-1004. Advisory 11B-236.1 General....
-
11B-236.1 General
At least one of each type of exercise machine and equipment shall comply with Section 11B-1004. Advisory 11B-236.1 General....