Commenters expressed concern about use of the terms "dining surfaces" and "work surfaces" and urged the Board to include definitions of the terms in the final rule....
Search Results "Concrete Surface"
-
Dining Surface and Work Surface
-
Selection of Trail Surface Materials
Selection of Trail Surface Materials A review of trail surfacing products conducted for this project identified approximately 80 different trail surface materials that promoted providing...
-
Exterior Surfaces
However, some natural surfaces, such as compacted earth, soil treated with consolidants, or materials stabilized and retained by permanent or temporary geotextiles (mesh), gridforms, or...
-
1017.2 Surface
This section requires the surface of trails, passing spaces, and resting intervals to be firm and stable. A firm trail surface resists deformation by indentations....
-
11B-1008.2.6 Ground surfaces
Ground surfaces on accessible routes, clear floor or ground spaces, and turning spaces shall comply with Section 11B-1008.2.6. Advisory 11B-1008.2.6 Ground surfaces....
-
11B-1008.2.6 Ground surfaces
Ground surfaces on accessible routes, clear floor or ground spaces, and turning spaces shall comply with Section 11B-1008.2.6. Advisory 11B-1008.2.6 Ground surfaces....
-
Acceptable Trail Surfacing Requirements
Trail surfaces are currently considered accessible only if the surfacing material is firm, stable, and slip-resistant and the trail has the engineered attributes of adequate width, moderately...
-
General: ADA Standard Section 302.1
Section 302.1 of the ADA Standards covers information in the current ADA Standards for floor or ground surfaces.
-
Floor and Ground Surfaces
This guide explains requirements in the ADA Standards for floor and ground surfaces. ...
-
T302.4 Surface Discontinuities
Surface discontinuities shall be ½ inch (13 mm) high maximum and shall be beveled with a slope not steeper than 1:2. EXCEPTIONS: 1....
-
1015.5 Surface
This section requires the surface of the clear ground space and turning space to be firm and stable....
-
Check Writing Surfaces: ADA Standard Section 904.3.3
Where provided, check writing surfaces shall comply with 902.3....
-
11B-505.8 Surfaces
Handrail gripping surfaces and any surfaces adjacent to them shall be free of sharp or abrasive elements and shall have rounded edges....
-
11B-505.8 Surfaces
Handrail gripping surfaces and any surfaces adjacent to them shall be free of sharp or abrasive elements and shall have rounded edges....
-
Bosch Power Tools - GPL-3 3 Point Laser
The Bosch Power Tools GPL 3 is a three-point, self-leveling laser with +/- 1/4 In. accuracy at 100 Ft. for up/down plumb, align and level applications. Unit includes point projection...
-
M-D Building Products, Inc. GEN3 SmartTool™ Digital Level
Water and DustProof IP65 Certified Hose off after concrete or muddy jobs Dustproof for the dirtiest environment Back Light Horizontal vial glows Easy-to-read in...
-
SafeLane® Surface Overlay in Action
Protecting people, roads and infrastructure, SafeLane® surface overlay from Cargill Deicing Technology is the only pavement overlay with anti-icing capabilities....
-
3.2.3 Surface
The ground surface in all camp living areas shall be firm and stable. The type of surface should be appropriate to the setting and level of development....
-
Performance for Surface Firmness and Stability
Performance for Surface Firmness and Stability Table 1 identifies the 11 test surface materials, the dates of installation, and the date of the initial and final testing of surfaces at...
-
11B-306.3.4 Clearance reduction
Exception: The knee clearance shall not be reduced at built-in dining and work surfaces required to be accessible by Section 11B-226.1....
-
11B-306.3.4 Clearance reduction
Exception: The knee clearance shall not be reduced at built-in dining and work surfaces required to be accessible by Section 11B-226.1....
-
Bonded Impact/cushioning Surfaces
Bonded Impact/cushioning Surfaces Eight different surface test specimens were formed with surface dimensions of 1.2m x 1.2m with a depth of 0.3m (48”x48”x 12”) in Madison WI (Figure 1...
-
4.7.4 Surface
Surfaces of curb ramps shall comply with 4.5....
-
4.7.4 SURFACE
Surfaces of curb ramps shall comply with 4.5....
