, fiberglass, or other manufactured material), it’s more difficult to ensure drainage on natural or gravel surfaces....
Search Results "Loose Fill Surface"
Filters
Commonly Searched Documents
-
Resting Intervals on Trails
-
11B-804.3.1 Clear floor or ground space
The clear floor or ground space shall be centered on the kitchen work surface and shall provide knee and toe clearance complying with Section 11B-306....
-
Bosch Power Tools - GPL-3 3 Point Laser
The Bosch Power Tools GPL 3 is a three-point, self-leveling laser with +/- 1/4 In. accuracy at 100 Ft. for up/down plumb, align and level applications. Unit includes point projection...
-
Cross Slope
Comment. Comments indicated that specifications for cross slope (1:48 maximum) are not referenced in the curb ramp section. Response. In the final rule, the Board has clarified...
-
1011.4.1 Height
The tops of picnic tables shall comply with 902.3.
-
Medical Diagnostic Equipment Accessibility Standards Sub-Committee Recommendations Imaging Equipment
Accessibility Standards for Medical Diagnostic Equipment Medical Diagnostic Equipment Accessibility Standards Sub-Committee Recommendations - Imaging Equipment Final...
-
Handrails
...are there handrails on both sides of the stair at a uniform height of 34"-38" above the front edge of the step? [ADA Stds. 4.9] Yes __ No __ N/A __ Comments:...
-
A5. Accessible Parking Spaces
A5. Are all accessible parking spaces, including the access aisle, relatively level (1:50 or 2%) in all directions? [ADA Stds 4.6.3] If No: Look for a nearby area that is relatively...
-
1011.4.1 Height
The tops of picnic tables shall comply with 902.3.
-
1.2.3 Landings
1.2.3 Landings. Both measurements of ramp landings as described in Section 1.1.15 should not exceed a plus tolerance of 0.5%.
-
1.2.7
1.2.7 When local variations (flatness) for cross slope of ramps are measured according to 1.1.14 at least 80% (rounded to the nearest whole number) should not exceed a 2% slope. The...
-
National Floor Safety Institute (NFSI)
Founded in 1997 the National Floor Safety Institute (NFSI) is a 501(c)(3) non-for-profit organization whose mission is: “to aid in the prevention of slips, trips, and falls through...
-
5.4.4.1 Transfer Support Distance from Transfer Surface Recommendation for Stretchers
surface on the opposite side of the transfer....
-
5.1.2 Transfer Surface High Height Recommendations for M301 and M302
5.1.2 Transfer Surface High Height Recommendations for M301 and M302 The Committee recommends an adjustable height range with an upper height measuring at least 25 inches....
-
5.2.1.4 Transfer Surface Size for Imaging Equipment
5.2.1.4 Transfer Surface Size for Imaging Equipment. The transfer surface should be 28 inches wide minimum and 21 inches deep minimum....
-
1133A.4, Item 2
A minimum linear length of 30 inches (762 mm) of countertop shall be provided for a work surface....
-
1133A.4, Item 2
A minimum linear length of 30 inches (762 mm) of countertop shall be provided for a work surface....
-
Boddingtons GrassCarpet™ Grass Protection Matting
GrassCarpet™ grass protection surface incorporates a heavy duty plastic reinforcement mesh bonded to a strong needle punched non-woven geotextile....
-
Varidesk Pro Desk Series: the Pro Desk 60
Check out our short video review of Varidesk's only stand alone standing desk: the Pro Desk 60. There are 5 different series of sit to stand adjustable desk from Varidesk. In this...
-
Pro Desk Series Description - VARIDESK
Short demonstration of the Pro Desk 60 by Varidesk.
-
Humanscale's Float Height-Adjustable Table
Float, Humanscale's Height-Adjustable desk meets the demands of healthier office solutions
-
Steelcase Ology Series height-adjustable tables
This is an informational video of the Steelcase Ology Series height-adjustable tables. We are working now more than ever -- more than any other single task in our lives, including...
-
902.4.2 Height
The tops of tables and counters shall be 26 inches (660 mm) minimum and 30 inches (760 mm) maximum above the finish floor or ground.
-
902.4.2 Height
The tops of tables and counters shall be 26 inches (660 mm) minimum and 30 inches (760 mm) maximum above the finish floor or ground.
