The transfer surface should be located such that the long dimension of 28 inches is located parallel to the patient scanning/imaging side of the table....
Search Results "Latch Side Clearance"
-
5.2.1.4 Transfer Surface Size for Imaging Equipment
-
Overhead Lifts
Overhead lifts may be the only option for certain diagnostic equipment because the structural or operational characteristics of the equipment prevent sufficient clearance in or around the...
- Bobrick Two-Wall Toilet Compartment Grab Bar B-5897
- Bobrick Two-Wall Toilet Compartment Grab Bar Peened B-6897.99
- Bobrick Two-Wall Toilet Compartment Grab Bar Peened B-5897.99
- Bobrick Two-Wall Toilet Compartment Grab Bar B-6897
- Access Board: Obstructed Forward Reach
-
1. Transfer Supports
The requirements were the same for transfer surfaces on diagnostic equipment used by patients in the supine, prone, or side-lying position, as well as diagnostic equipment used by patients...
-
M301.2.2 Transfer Surface Size
When the transfer surface is located as described above in “A”, the width of the patient scanning/imaging table (side to side) at the designated transfer location should be 28 inches minimum...
-
5.4.1 Transfer Support Location for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.1 Transfer Support Location for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
Positioning Supports Considered
The Board is considering requiring in the final standards positioning supports such as rails, bars, or panels with handholds to be provided along the sides of diagnostic equipment used by...
-
11B-233.3.1.2.6.5 Additional requirements.
Door maneuvering clearance complying with Section 11B-809.8. 6. Water closet seat height complying with Section 11B-809.10.7.4. 7....
-
11B-204.1 General
Within play areas, protruding objects on circulation paths shall not be required to comply with Section 11B-307 provided that ground level accessible routes provide vertical clearance in...
-
11B-204.1 General
Within play areas, protruding objects on circulation paths shall not be required to comply with Section 11B-307 provided that ground level accessible routes provide vertical clearance in...
- American Standard Acrylic Shroud for American Standard Selectronic Faucets
-
T502.2.1 Over-the-Road Buses
For over-the-road buses, the vertical clearance at doorways shall be 65 inches (1650 mm) minimum....
-
5.4.1.2 Transfer and Positioning Support Location for Imaging Equipment
The transfer supports or positioning supports should be located opposite the transfer side....
-
M301.3.3 Head and Back Support
M301.3.3 Head and Back Support Proposed requirement: Where diagnostic equipment used by patients in a supine, prone, or side-lying position, and diagnostic equipment used by patients...
-
Stirrups (M301.3.2)
Where stirrups are provided on diagnostic equipment used by patients in a supine, prone, or side-lying position, M301.3.2 would require the stirrups to provide a method of supporting, positioning...
- Access Board: Toilet Rooms
-
5.4.10 Transfer Support Fittings for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.10 Transfer Support Fittings for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
Check-Out Aisles and Sales and Service Counters
Where the counter is a split-height counter, this requirement applies only to the customer side of the counter top....
-
Supports (M301.3, M302.3, and M305.2)
M301.3, M302.3, and M305.2 provide technical criteria for transfer and positioning supports on diagnostic equipment used by patients in a supine, prone, or side-lying position, and diagnostic...
-
5.6.1 Stirrups Provision for M301
5.6.1 Stirrups Provision for M301 NPRM Description: For patients with limited leg strength and control, thigh, knee and calf supports are necessary to maintain an appropriate...