Kitchens shall have a minimum clear width measured between any cabinet, work surface or the face of any appliance (excluding handles and controls) and the opposing cabinet, work...
Search Results "Residential Structure"
Filters
Commonly Searched Documents
-
11B-809.9.2 Clear width
-
Harmar RPL Residential Vertical Platform Lift
Harmar’s Residential Vertical Platform Lift (RPL) is a safe, smooth and economical solution to the barriers porches, staircases, decks and other elevation changes can create in and around...
-
Sec.36.403(a) General
(a) General. An alteration that affects or could affect the usability of or access to an area of a facility that contains a primary function shall be made so as to ensure that, to...
-
§ 36.403(a)
(a) * * *
-
Path of travel
The path of travel to the altered or added portion of the facility must be made accessible, to the maximum extent feasible. (DOT ADA Regulation 49 C.F.R. 37.43(a)(2) and DOT ADA...
-
§ 36.403(a) General.
(a) General.
-
1019.1 General
b) (iv) and 800.7 (c) (4)); and • Provisions in the Wilderness Act that require federal agencies to preserve the wilderness character of designated wilderness areas and prohibit any structure...
-
1019.1 General
(iv) and 800.7 (c) (4)); and Provisions in the Wilderness Act that require federal agencies to preserve the wilderness character of designated wilderness areas and prohibit any structure...
-
F206.2.3 Multi-Story Buildings and Facilities
In residential facilities, an accessible route shall not be required to connect stories where residential dwelling units with mobility features required to comply with 809.2 through 809.4...
-
11B-407.4.10.3 Structural strength
shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the support rail, fastener, mounting device, or supporting structure...
-
F202.4 Alterations Affecting Primary Function Areas
Residential dwelling units shall not be required to comply with F202.4. 2. ...
-
11B-809.9.1 Clear floor space
Clear floor spaces 30 inches (762 mm) by 48 inches (1219 mm), with centerlines aligned with the centerline of the work surface, appliance, sink or fixture, shall be provided in the...
-
11B-809.10.4 Sufficient maneuvering space
Where doors swing into the toilet and bathing or powder rooms required to comply with Section 11B-809.10, a clear maneuvering space of 30 (762 mm) inches by 48 inches (1219 mm)...
-
11B-205.1 General
In residential dwelling units with mobility features where receptacles are provided in a kitchen at a corner work surface, one receptacle shall be located 36 inches (915 mm) from either...
-
Section 35.151(b) Alterations (Section-by-Section Analysis)
The Department's proposed rule would amend § 35.151(b)(2) to make clear that the path of travel requirements of § 35.151(b)(4) do not apply to measures taken solely to comply with...
-
§ 35.151(b) Alteration
(b) Alteration.
-
Exemptions for Entire Trail or Beach Access Route
The proposed rule would have exempted an entire trail from complying with the technical requirements for trails when: The combination of running slope and cross slope...
-
§ 35.151(b) Alterations.
(b) Alterations.
-
§ 37.43 Alteration of transportation facilities by public entities
[See subsections ...]
-
11B-809.10.8.1 Location
Lavatories without base cabinets shall be installed with the centerline 18 inches (457 mm) minimum from an adjoining wall or fixture to allow for forward approach. Lavatories with...
-
11B-809.10.8.5 Plumbing protection
Plumbing protection shall comply with Section 11B-809.9.7.
-
11B-809.10.5.3 Controls
Controls and operating mechanisms shall comply with Section 11B-309.4. Exception: Shower spray units are not required in bathtubs.
-
11B-809.10.8 Lavatories, vanities, mirrors and towel bars
Bathing rooms or powder rooms required to comply with Section 11B-809.10 shall provide lavatories complying with this section. Where mirrors or towel bars are provided, no less than...
-
11B-809.10.8.4 Knee and toe clearance
Knee and toe clearance shall be provided and comply with Section 11B-306.
