Qualified individual with a disability means an individual with a disability who satisfies the requisite skill, experience, education and other job-related requirements of the employment position...
Search Results "Positioning Support"
-
1630.2(m) Qualified individual with a disability
-
12114(c)(5)(C)
employees of the covered entity are employed in a transportation industry subject to such regulations, including complying with such regulations (if any) that apply to employment in sensiive positions...
-
12114(c)(5)(C)
employees of the covered entity are employed in a transportation industry subject to such regulations, including complying with such regulations (if any) that apply to employment in sensitive positions...
-
Service Animal:
With respect to emotional support animals, although carriers may require documentation to verify that an animal is an emotional support animal, such documentation is not required under the...
-
6. Minimum (Low) Height Standard for Transfer Surfaces
Recommendations split across three options: 17”; 18”, which was viewed by some proponents as a compromise position and by others as their preferred minimum height; and 19”....
-
Chapter 4: Creating a Workable ADA: The Senate and the White House
In fact, a poll of voter intentions on the eve of the election, conducted by Louis Harris and Associates, suggested that the wide margin of persons with disabilities supporting Bush was...
-
§ 38.83(c)(1) Design load
Ramps or bridge plates 30 inches or longer shall support a load of 600 pounds, placed at the centroid of the ramp or bridge plate distributed over an area of 26 inches, with a safety factor...
-
H. Barriers Affecting Accessibility and Usability of Medical Diagnostic Equipment
Survey respondents reported difficulties with getting on and off the equipment, positioning their bodies on the equipment, physical comfort and safety, and communication issues....
-
11B-606.6 Adjacent side wall or partition
ETA Editor's Note The positioning requirement prescribed by CBC 11B-606.6 applies to lavatories, not to sinks....
-
11B-606.6 Adjacent side wall or partition
ETA Editor's Note The positioning requirement prescribed by CBC 11B-606.6 applies to lavatories, not to sinks....
-
12114(c)(5)(B)
Commission, if the employees of the covered entity are employed in an industry subject to such regulations, including complying with regulations (if any) that apply to employment in sensitive positions...
-
12114(c)(5)(B)
Commission, if the employees of the covered entity are employed in an industry subject to such regulations, including complying with regulations (if any) that apply to employment in sensitive positions...
-
M303 Diagnostic Equipment Used by Patients Seated in Wheelchair
M303 allows patients who use wheelchairs to position their wheelchairs at equipment typically used in a standing position such as mammography equipment, and also applies to equipment specifically...
-
NABCO GT300 & GT8300 Overhead Concealed Low-Energy Swing Door Operator
The door is supported by heavy-duty pivots on the top and bottom of the doorframe instead of on the operator shaft, which allows for convenient servicing without removing the door....
-
Philips Healthcare
the consensus of the committee PLEASE NOTE: If you disagree with any of the recommendations included in the report, you are encouraged to submit a Minority Report describing your position...
-
General: ADA Standard Section 306.1
Section 306.1 of the ADA Standards covers information in the current ADA Standards for knee and toe clearance.
-
11B-1009.2 Pool lifts
Additional options such as armrests, head rests, seat belts, and leg support will enhance accessibility and better accommodate people with a wide range of disabilities. ◼...
-
11B-1009.2 Pool lifts
Additional options such as armrests, head rests, seat belts, and leg support will enhance accessibility and better accommodate people with a wide range of disabilities. ◼...
-
C201.1 Scope
Manufacturers shall also conform to the requirements in the Revised 255 Guidelines for support documentation and services, including electronic documents and Web-based product support....
-
§ 38.125(c)(1) Design load
Ramps or bridge plates 30 inches or longer shall support a load of 600 pounds, placed at the centroid of the ramp or bridge plate distributed over an area of 26 inches by 26 inches, with...
-
§ 38.95(c)(1) Design load
Ramps or bridge plates 30 inches or longer shall support a load of 600 pounds, placed at the centroid of the ramp or bridge plate distributed over an area of 26 inches by 26 inches, with...
-
21. How should an employer handle leave for an employee covered by both the ADA and the Family and Medical Leave Act (FMLA)?
If it is an undue hardship under the ADA to hold open an employee's position during a period of leave, or an employee is no longer qualified to return to his/her original position, then...
-
7. What remedies address violations of the ADA’s integration mandate in the context of disability employment systems?
The Department has entered into settlement agreements that require states to expand the services and supports available in integrated employment settings....
-
(3) Adjustability: Transfer Surface Intermediate Heights
Three commenters responded (two accessibility consultants and a disability rights advocate) and supported the idea of requiring intermediate heights within a minimum low height and minimum...
