Ground surfaces located within use zones shall comply with ASTM F 1292 (1999 edition or 2004 edition)....
Search Results "Door Surface"
-
11B-1008.2.6.2 Use zones
-
11B-409.4.2 Floor surfaces
Floor surfaces in elevator cars shall comply with Sections 11B-302 and 11B-303....
-
11B-409.4.2 Floor surfaces
Floor surfaces in elevator cars shall comply with Sections 11B-302 and 11B-303....
-
11B-409.4.2 Floor surfaces
Floor surfaces in elevator cars shall comply with Sections 11B-302 and 11B-303....
-
404.3.1 Clear Width
The minimum clear width for automatic door systems in a doorway shall be based on the clear opening provided by all leaves in the open position. [ECTCR UFAS 4.13.5]...
-
404.3.1 Clear Width
The minimum clear width for automatic door systems in a doorway shall be based on the clear opening provided by all leaves in the open position....
-
404.2.7 Door and Gate Hardware
Handles, pulls, latches, locks, and other operable parts on doors and gates shall comply with 309.4....
-
404.2.7 Door and Gate Hardware
Handles, pulls, latches, locks, and other operable parts on doors and gates shall comply with 309.4....
-
H6
If the entry has a vestibule, is there a 30-inch by 48-inch clear floor space inside the vestibule where a wheelchair or scooter user can be outside the door swing?...
-
R308.1.3.1 Surfaces
R308.1.3.1 Surfaces. The surfaces of boarding and alighting areas and boarding platforms shall comply with R302.7. Advisory R308.1.3.1 Surfaces....
-
505.8 Surfaces
505.8 Surfaces. Handrail gripping surfaces and any surfaces adjacent to them shall be free of sharp or abrasive elements and shall have rounded edges....
-
Is there a minimum distance between changes in level?
span vertical changes greater than ½”, must have level landings and clearances at the tops and bottoms of each run to provide adequate separation and resting intervals between sloping surfaces...
-
Employee Work Areas: ADA Standard Section 203.9
Section 203.9 covers scoping requirements of general exceptions for employee work areas in the most current ADA Standards.
-
11B-504.4 Tread surface
Stair treads shall comply with Section 11B-302. Changes in level are not permitted. Exception: Treads shall be permitted to have a slope not steeper than 1:48.
-
11B-504.4 Tread surface
Stair treads shall comply with Section 11B-302. Changes in level are not permitted. Exception: Treads shall be permitted to have a slope not steeper than 1:48.
-
Besam SL500 A02 for sustainable automatic doors
The automatic sliding door Besam SL500 from ASSA ABLOY Entrance Systems has directional sensors. The door optimizes closing to reduce energy loss after passing through the door....
-
Thresholds at Doorways
The 1991 Standards, at section 4.13.8, require the height of thresholds at doorways not to exceed ½ inch and thresholds at exterior sliding doors not to exceed ¾ inch....
-
H2
Does the door to the toilet room provide at least 32 inches clear passage width when the door is open 90 degrees? [ADA Standards § 4.13.5] Yes No...
-
M2
Does the door to the toilet room provide at least 32 inches clear passage width when the door is open 90 degrees? [ADA Standards § 4.13.5] Yes No...
-
1.2.1 Walks and other non - ramp surfaces
1.2.1 Walks and other non - ramp surfaces. When overall running slope for walks is measured according to Section 1.1.3 a recommended tolerance for running slope is +1%....
-
T302 Walking Surfaces
[See subsections ...]
-
(4) [sic] Thresholds at exterior doors
Subject to the exceptions for thresholds and changes in level at exterior areas constructed of impervious materials, the final Guidelines continue to specify that thresholds at exterior doors...
-
Surfaces (R302.7) (Section-by-Section Analysis)
Surfaces (R302.7) (Section-by-Section Analysis) The proposed technical requirements for surfaces apply to pedestrian access routes, including curb ramps and blended transitions, and accessible...
-
Restrooms Main Lobby
The restroom vestibule door does not have the required minimum of 18" maneuvering clearance on the latch side of the door. See Standards § 4.13.6. l....
