Grab bars shall be installed in any manner that provides a gripping surface at the specified locations and that does not obstruct the required clear floor space....
Search Results "Dining Surface"
Filters
Commonly Searched Documents
-
609.7 Installation
-
609.7 Installation
Grab bars shall be installed in any manner that provides a gripping surface at the specified locations and that does not obstruct the required clear floor space....
-
§ 38.99(a)
(a) Floor surfaces on aisles, step treads, places for standees, and areas where wheelchair and mobility aid users are to be accommodated shall be slip-resistant...
-
11B-609.7 Installation
Grab bars shall be installed in any manner that provides a gripping surface at the specified locations and that does not obstruct the required clear floor space....
-
11B-805.7 Built-in cabinets and work surfaces
Built-in cabinets, counters and work surfaces shall be accessible, including: patient wardrobes, nurse’s stations, administrative centers, reception desks, medicine preparation areas, laboratory...
-
505.1 General
Handrails provided along walking surfaces complying with 403, required at ramps complying with 405, and required at stairs complying with 504 shall comply with 505....
-
609.7 Installation
Grab bars shall be installed in any manner that provides a gripping surface at the specified locations and that does not obstruct the required clear floor space....
-
11B-609.7 Installation
Grab bars shall be installed in any manner that provides a gripping surface at the specified locations and that does not obstruct the required clear floor space....
-
2. Standing Supports
For horizontal standing supports, the Access Board proposed a gripping surface of 4 inches long minimum, the top of which would be required to be located 34 inches minimum and 38 inches...
-
Starodub, Inc. Ultra-Light Inertial Profiler (ULIP) for Sidewalks
ULIP Ultra-Light Inertial Profiler ULIP is a Segway based sensor and acquisition system for collecting pavement surface data for the computation of ride quality, surface texture,...
-
How to Measure Transfer Surface Height
How to Measure Transfer Surface Height Regardless of the final decision on the low height measurement, the Subcommittee agreed that the height of the transfer surface would be measured...
-
Clearances Around Gripping Surfaces
Guidelines specify the following clearances around grab bars to ensure sufficient space for a person to grasp the grab bar: 1½ inches absolute clearance between grab bars and the adjacent wall surfaces...
-
Mockett TLRAL27 Roma Series Adjustable Table Leg
You may need 27" on the office desk, 29" on the dining table, and 33" on the wheelchair accessible table. Roma Leg does them all! Takes five seconds to change height. It's that easy....
-
(2) Transfer Surface Location for Diagnostic Equipment Used in the Seated Position
Transfer onto these types of diagnostic equipment must be made from either long side, similar to the side transfer surface described above....
-
§ 38.125(b)(6) Platform surface
(6) Platform surface. The lift platform surface shall be free of any protrusions over 1/4 inch high and shall be slip resistant....
-
Check-Out Aisles [7.3]
Writing surfaces must be 36 inches maximum from the floor....
-
UltraPlay Getting Started Installation Video
Learn how to get started and prepare for the installation of your UltraPlay playground structure with this first of several installation videos.
-
AccessRec AccessMat Beach Access Mat System
Comfortable and Safe Developed specifically for pedestrian traffic, AccessMat™ provides a barefoot friendly surface for beach goers....
-
Poured in Place Rubber
The surface cost for PIP ranged from $6.59/sq. ft. to $19.80/sq. ft. ...
-
The Brewer Company, LLC
Company, LLC Minority Report The Brewer Company, LLC 01-Oct-2013 Final Report Medical Diagnostic Equipment Accessibility Standards Advisory Committee Section 5.1.3 Transfer Surface...
-
M305.2.5 Surface Hazards (Section-by-Section Analysis)
No public comments were submitted on this issue, but the MDE Advisory Committee voiced concern about surface hazards stating, “gripping surface configurations must provide an effective and...
-
405.3 Cross Slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
405.3 Cross Slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
5.1.1 Transfer Surface Height Adjustability
5.1.1 Transfer Surface Height Adjustability. The transfer surface should have an adjustable height in small virtually continuous increments....
