Companion seats shall be equivalent in size, quality, comfort, and amenities to the seating in the immediate area. Companion seats shall be permitted to be movable....
Search Results "Designated Aisle Seat (Assembly)"
-
11B-802.3.2 Type
-
4.1.3(19)(b)
(b) This paragraph applies to assembly areas where audible communications are integral to the use of the space (e.g., concert and lecture halls, playhouses and movie theaters, meeting rooms...
-
802.3.2 Type
Companion seats shall be equivalent in size, quality, comfort, and amenities to the seating in the immediate area. Companion seats shall be permitted to be movable....
-
Angled (Front-In) Parking
ADAAG's requirement for an access aisle on either side of a space (they can be shared by two spaces) is based on the assumption that drivers can head in or back in as needed....
-
IV. Priority Seating Signs and Other Signage
Priority Seating Signs and Other Signage...
-
Seating Solutions ADA Platforms, Ramps & Stairs
We will design and build to meet your specific requirements....
-
1008.4.4 Entry Points and Seats
Where play components require transfer to entry points or seats, the entry points or seats shall be 11 inches (280 mm) minimum and 24 inches (610 mm) maximum from the clear floor or ground...
-
1008.4.4 Entry Points and Seats
Where play components require transfer to entry points or seats, the entry points or seats shall be 11 inches (280 mm) minimum and 24 inches (610 mm) maximum from the clear floor or ground...
-
1009.2.2 Seat Location
1009.2.2 Seat Location. In the raised position, the centerline of the seat shall be located over the deck and 16 inches (405 mm) minimum from the edge of the pool....
-
§ 35.138(h)(2)
A public entity may investigate the potential misuse of accessible seating where there is good cause to believe that such seating has been purchased fraudulently....
-
11B-227.5 Queues and Waiting Lines
Queues and waiting lines servicing counters or check-out aisles required to comply with Sections 11B-904.3 or 11B-904.4 shall comply with Section 11B-403....
-
11B-227.5 Queues and Waiting Lines
Queues and waiting lines servicing counters or check-out aisles required to comply with Sections 11B-904.3 or 11B-904.4 shall comply with Section 11B-403....
-
Toilets
Provide a toilet seat that is 17" to 19" above the finished floor in the north women's toilet room located in the "Celebrity Spies" exhibit area. See Standards § 4.16.3....
-
American Society of Interior Designers (ASID)
The American Society of Interior Designers (ASID) is a community of people — designers, industry representatives, educators and students — committed to interior design....
-
Big John Original Toilet Seat Open Front Less Cover - 4W
The Big John Toilet Seat has a larger, more comfortable opening and a luxuriously contoured sitting surface that is roomier than any other toilet seat on the market....
-
Can curb ramps overlap access aisles?
No, access aisles, as well as vehicle pull-up spaces, cannot have changes in level other than slopes not exceeding 1:48....
-
11B-610.4 Structural strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or...
-
610.4 Structural Strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or...
-
610.4 Structural Strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or...
-
11B-610.4 Structural strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or...
-
1012.3 Opening limitations
In assembly seating areas, guards at the end of aisles where they terminate at a fascia of boxes, balconies and galleries shall have balusters or ornamental patterns such that a 4-inch-diameter...
-
1002.4.7 Companion Seats
1002.4.7 Companion Seats....
-
isUD - Innovative Solutions for Universal Design
This legitimizes design decisions and makes universal design a more powerful force for improving design quality overall....
-
610.4 Structural Strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or...
