For purposes of paragraphs (a) through (c) of this section, the term "individual or class of individuals" refers to the clients or customers of the public accommodation that enters into...
Search Results "Vertical Reference Plane"
-
§ 36.202(d) Individual or class of individuals.
-
Sec.36.202(d) Individual or class of individuals
For purposes of paragraphs (a) through (c) of this section, the term "individual or class of individuals'' refers to the clients or customers of the public accommodation that enters into...
-
COMMON USE
Refers to those interior and exterior rooms, spaces, or elements that are made available for the use of a restricted group of people (for example, residents of an apartment building, the...
-
408.3.2.1 Power Operation
Swinging doors shall be power-operated and shall comply with ANSI/BHMA A156.19 (1997 or 2002 edition) (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
R408.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
Running Slope
This may be expressed as the percentage of change in elevation (grade) or as a ratio of vertical distance to horizontal distance (running slope)....
-
Edge Protection [§405.9]
Edge protection is not required at: ramps no higher than 6” that have side flares ramp landings serving an adjoining run or stairway sides of ramp landings with vertical...
-
11B-704.5 TTY shelf
The shelf shall be capable of accommodating a TTY and shall have 6 inches (152 mm) minimum vertical clearance above the area where the TTY is to be placed....
-
§ 38.159(b)(10) Platform movement
The maximum platform horizontal and vertical acceleration when occupied shall be 0.3g....
-
‘‘Designated agency.’’
The term ‘‘designated agency’’ is used to refer to the Federal agency designated under subpart G of this rule as responsible for carrying out the administrative enforcement responsibilities...
-
602.3 Electronic Support Documentation
Documentation in electronic format, including Web-based self-service support, shall conform to Level A and Level AA Success Criteria and Conformance Requirements in WCAG 2.0 (incorporated by reference...
-
10. Remember that disability is not an illness and people with disabilities are not patients.
Only refer to someone as a patient when his or her relationship with a health care provider is under discussion....
-
Designated agency (Section-by-Section Analysis)
The term "designated agency" is used to refer to the Federal agency designated under subpart G of this rule as responsible for carrying out the administrative enforcement responsibilities...
-
8.1 General
In addition to the requirements of 4.1 to 4.35, the design of all public areas of a library shall comply with 8, including reading and study areas, stacks, reference rooms, reserve areas...
-
Unitary Surface
Unitary surfaces may include asphalt, concrete, rubber mats, tiles or a rubber fill product chemically bound and often referred to as “poured-in-place.” ...
-
13.2 ADA Standards
13.2 “ADA Standards” shall mean and refer to the Standards for Accessible Design as set forth at 28 C.F.R. pt. 36, Appendix A, published in 28 C.F.R. Part 36 (July 1, 2004)....
-
M305.2 Transfer Supports
M305.2 Transfer Supports M305.2.2 Transfer Supports Structural Strength Proposed requirement: Transfer supports and their connections shall be capable of resisting vertical and...
-
Sight Lines
Sight Lines Both the horizontal and vertical viewing angles must be considered in the design of assembly areas....
-
Transfer Supports (M301.3.1, M302.3.1, and M305.2)
M305.2.2 would require the transfer supports and their connections to be capable of resisting vertical and horizontal forces of 250 pounds applied to all points of the transfer support....
-
206.2.4 Spaces and Elements
Exceptions 1 – 3 are preempted by Florida vertical accessibility requirements of s.553.509, F.S., as incorporated in section 201.1.1....
-
11B-504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
11B-504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
M301.2.1, M302.2.1 Transfer Height
These surfaces may range between 4” to 5” in thickness - this will add to the vertical height of a stretcher when measuring from the floor to the top of the surface (uncompressed)....
-
206.2.3 Multi-Story Buildings and Facilities
Exceptions 1 – 7 are preempted by Florida vertical accessibility requirements of s. 553.509, F.S., as incorporated in section 201.1.1....