A clear floor or ground space complying with Section 11B-305 shall be provided in the load and unload area adjacent to the transfer device....
Search Results "Transfer Side"
-
11B-1002.6.1 Clear floor or ground space
-
4. Exception from the Requirements of M301 for Certain Examination Chairs that Comply with M302
These commenters argued that requiring the equipment to be designed to accommodate transfer in both positions would not achieve any objective benefit and would impose transfer surface width...
-
1002.6.1 Clear Floor or Ground Space
A clear floor or ground space complying with 305 shall be provided in the load and unload area adjacent to the transfer device....
-
11B-406.5.10 Diagonal curb ramps
Diagonal curb ramps with flared sides shall have a segment of curb 24 inches (610 mm) long minimum located on each side of the curb ramp and within the marked crossing....
-
Brey-Krause Concealed Mounting Security / Anti Suicide Grab Bars
The concealed mount anti-ligature grab bars are fabricated from 18 gauge stainless steel. The flange is constructed from 11 gauge stainless steel and is three inches in diameter....
-
Behavioral Safety Products #GB350 Suicide Resistant Safety Grab Bar with Full Closure Plate
Product Description We offer this suicide resistant grab bar in seven lengths: 18", 24", 30", 32", 36", 42", and 48". All lengths except for the 18" and 32" are available for...
-
1014.2.1.1.2 Slope
The slope of the surface of the clear ground space shall not be steeper than 1:48 in any direction. EXCEPTION: Where the surface is other than asphalt, concrete, or boards, slopes...
-
4.21.4 Grab Bars
Grab bars complying with 4.26 shall be provided as shown in Fig. 37.
-
1014.2.1.1.2 Slope
The slope of the surface of the clear ground space shall not be steeper than 1:48 in any direction. EXCEPTION: Where the surface is other than asphalt, concrete, or boards, slopes...
-
4.21.4 GRAB BARS
Grab bars complying with 4.26 shall be provided as shown in Fig. 37. Figure 37 Grab Bars at Shower Stalls
-
5.7.1 Lift Compatibility Clearance in Base for Equipment Used by Patient in Supine, Prone, or Side-Lying Position
5.7.1 Lift Compatibility Clearance in Base for Equipment Used by Patient in Supine, Prone, or Side-Lying Position....
-
Built-Up Curb Ramps
Built-Up Curb Ramp with Side Flares Recommendations: Provide edge protection along the sides of built-up curb ramps to prevent tipping hazards....
-
Figure 404.2.4.3(a) Maneuvering Clearance at Recessed Doors and Gates – Drawing from the U.S. Access Board
-
§ 38.123(a)(3)
(3) A grab bar at least 24 inches long shall be mounted behind the water closet, and a horizontal grab bar at least 40 inches long shall be mounted on at least one side wall, with one end...
-
(1)(c)
(c) A grab bar at least 24 inches (610 mm) long should be mounted behind the water closet, and a horizontal grab bar at least 40 inches (1015 mm) long should be mounted on at least one side...
-
Typical Transfer Techniques: Staff Assistance and Patient Lifts
Some individuals will need only a steady hand from a staff person in order to transfer safely to the exam table....
-
Bobrick Two-Wall Toilet Compartment Grab Bar B-5897
42" W x 54" D (107 x 137cm), 1-1/4" (32mm) dia. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm) thick, type 304...
-
Bobrick Two-Wall Toilet Compartment Grab Bar B-6897
42" W x 54" D (107 x 137cm), 1-1/2" (38mm) dia. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm) thick, type 304...
-
Bobrick Two-Wall Toilet Compartment Grab Bar Peened B-5897.99
42" W x 54" D (107 x 137cm), 1-1/4" (32mm) dia., peened finish. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm)...
-
Bobrick Two-Wall Toilet Compartment Grab Bar Peened B-6897.99
42" W x 54" D (107 x 137cm), 1-1/2" (38mm) dia., peened finish. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm)...
-
4.34.3(2)(b) Reach Depth More Than 10 in
(b) Reach Depth More Than 10 in (255 mm). Where the reach depth to the operable parts of any control as measured from the vertical plane perpendicular to the edge of the unobstructed...
-
4.34.3(2)(a) Reach Depth Not More Than 10 in
(a) Reach Depth Not More Than 10 in (255 mm). Where the reach depth to the operable parts of all controls as measured from the vertical plane perpendicular to the edge of the...
-
A4.27.3 HEIGHT
Fig. A6 further illustrates mandatory and advisory control mounting height provision for typical equipment. Note distinction between built-in equipment (considered real property) and...
