and local governments must comply with the requirements for protruding objects and maintain the clear width of pedestrian access routes when installing or permitting the installation of street...
Search Results "On-Street Bus Stop"
-
R210 Protruding Objects
-
218 Transportation Facilities
Section 218 provides requirements for rail stations, fixed guideway systems, bus shelters, and other transit facilities, such as airports....
-
VEHICULAR WAY
A route provided for vehicular traffic, such as in a street, driveway, or parking facility....
-
Vehicular Way
A route provided for vehicular traffic, such as in a street, driveway, or parking facility....
-
407.4.7.1.3 Symbols
The control button for the emergency stop, alarm, door open, door close, main entry floor, and phone, shall be identified with tactile symbols as shown in Table 407.4.7.1.3....
-
Other Features
These may include Braille labels for street names, actuation indicators (a light or beep), tactile crosswalk maps, and options activated by an extended button push: audible beaconing (useful...
-
R304.2.3 Flared Sides
Curb ramps whose sides have returned curbs provide useful directional cues where they are aligned with the pedestrian street crossing and are protected from cross travel by landscaping,...
-
II-6.6000 Curb ramps
When streets, roads, or highways are newly built or altered, they must have ramps or sloped areas wherever there are curbs or other barriers to entry from a sidewalk or path....
-
11B-406.5.8 Counter slope
The adjacent surfaces at transitions at curb ramps to walks, gutters, and streets shall be at the same level. [2010 ADA Standards] 406.2 Counter Slope....
-
Section 2. Vehicular route
"Vehicular route" means a route intended for vehicular traffic, such as a street, driveway or parking lot....
-
Clear Width at Turn: ADA Standard Section 403.5.2
Section 403.5.2 covers the current ADA Standards for the clear width at a turn on walking surfaces that are part of an accessible route.
-
Construction and Manufacturing Tolerances: ADA Standard Section 104.1.1
Section 104.1.1 of the ADA Standards covers the most current information on dimensions in regards to construction and manufacturing tolerances in the ADA Standards.
-
General: ADA Standard Section 223.1
Section 223.1 of the ADA Standards covers information in the current ADA Standards on scoping requirements for medical care and long-term care facilities.
-
Hospital Outpatient Facilities: ADA Standard Section 208.2.1
Section 208.2.1 of the ADA Standards covers information on scoping requirements in the most current ADA Standards for accessible parking at hospital outpatient facilities.
-
12141(2) Designated public transportation
(2) Designated public transportation The term "designated public transportation" means transportation (other than public school transportation) by bus, rail, or any other conveyance (...
-
Issue 15: Installation Errors Increase Risk
Before he could step into the street, he was stopped, and the change of the APS was explained to him....
-
Issue 7: Repair/replacement (put it back right!)
After reinstallation, the APS was turned 90 degrees from its prior placement, and the tactile arrow was no longer pointing at the street the pushbutton controlled....
-
R208.2 Where Not Required
Detectable warning surfaces are not required at pedestrian refuge islands that are cut-through at street level and are less than 1.8 meters (6.0 ft) in length in the direction of pedestrian...
-
11B-409.4.4 Leveling
Each car shall automatically stop at a floor landing within a tolerance of ½ inch (12.7 mm) under rated loading to zero loading conditions....
-
409.4.4 Leveling
Each car shall automatically stop at a floor landing within a tolerance of ½ inch (13 mm) under rated loading to zero loading conditions....
-
4.1.6(3)(d)(i)
(i) Where it is technically infeasible to comply with clear opening width requirements of 4.13.5, a projection of 5/8 in maximum will be permitted for the latch side stop....
-
11B-409.4.4 Leveling
Each car shall automatically stop at a floor landing within a tolerance of ½ inch (12.7 mm) under rated loading to zero loading conditions....
-
11B-409.4.4 Leveling
Each car shall automatically stop at a floor landing within a tolerance of ½ inch (12.7 mm) under rated loading to zero loading conditions....