Where equipment is designed to support more than one patient position, the equipment would have to meet the technical criteria for each position supported....
Search Results "Elevator Car Position Indicator"
-
4. Organization of Technical Criteria
-
11B-407.2 Elevator landing requirements
Elevator landings shall comply with Section 11B-407.2....
-
11B-407.2 Elevator landing requirements
Elevator landings shall comply with Section 11B-407.2....
-
11B-407.2 Elevator landing requirements
Elevator landings shall comply with Section 11B-407.2....
-
Standing Supports (M304.3 and M305.3)
Standing supports can be provided in a horizontal position, vertical position, or a combination of horizontal and vertical positions, as long as the minimum length of gripping surface is...
-
Transfer Supports Location and Configuration M301.3 and M302.3
The length of the transfer support shall be a minimum of 15 inches long and positioned so that the transfer support overlaps the length of the transfer surface by 80% at a maximum distance...
-
§ 38.95(b)(4) Power or equipment failure
Platforms stowed in a vertical position, and deployed platforms when occupied, shall have provisions to prevent their deploying, falling, or folding any faster than 12 inches/second or their...
-
M301.3 Transfer Supports
Transfer Supports Position • Sub-Committee Recommendation: Located longitudinally within the long side of the of the transfer surface....
-
5.2.2 Transfer Surface Size for Equipment Used by Patients in Seated Position
5.2.2 Transfer Surface Size for Equipment Used by Patients in Seated Position....
-
Paragraph (f) Prevention of visually induced seizures (Section-by-Section Analysis)
The NPRM suggested that the flash rate for visual indicators be set at or below 3 Hz, based on research for visual fire alarms, and asked (Question 8) whether this value was appropriate....
-
5.2.1.3 Transfer Surface Size for Stretchers
5.2.1.3 Transfer Surface Size for Stretchers. The transfer surface should be 28 inches wide minimum and 17 inches deep minimum located on both long sides of stretchers.
-
5.4.1.1 Transfer Support Location for Stretchers
5.4.1.1 Transfer Support Location for Stretchers. The transfer surface for stretchers should be oriented along the long side of the surface.
-
Are freight or service elevators required to comply?
When an elevator is used to provide a required accessible route between stories, it must meet requirements for passenger elevators....
-
Transfer Surface (M301.2 and M302.2)
The technical criteria in M301.2 and M302.2 address the height and size of the transfer surface, and the transfer sides. The transfer surface is the part of the diagnostic equipment...
-
E1-5. Elevator
Is an elevator provided to access the voting area level? Yes _____ No _____...
-
3001.4 Accessibility
Passenger elevators and platform (wheelchair) lifts required to be accessible or to serve as part of an accessible means of egress shall comply with Sections 1009 and either Chapter 11A...
-
3001.4 Accessibility
Passenger elevators and platform (wheelchair) lifts required to be accessible or to serve as part of an accessible means of egress shall comply with Sections 1009 and either Chapter 11A...
-
§ 38.125(b)(2)(i) Requirements
The controls shall be interlocked with the car brakes, propulsion system, or door, or shall provide other appropriate mechanisms or systems, to ensure that the car cannot be moved when the...
-
11B-407 ELEVATORS
[See subsections ...]
-
11B-407 Elevators
[See subsections ...]
-
11B-407 Elevators
[See subsections ...]
-
Hall Lanterns [4.10.4]
Audible signals serve people with visual impairments by indicating which car is answering the call and its travel direction....
-
§ 38.111(a)(4)
(4) Bi-level lounge cars shall have doors on the lower level, on each side of the car from which passengers board, complying with §38.113, a restroom complying with §38.123, and at least...
-
408.2 Elevator Landings
Landings serving limited-use/limited-application elevators shall comply with 408.2....