The ½ inch horizontal maximum specified for gratings is a good rule of thumb for these openings as well....
Search Results "Horizontal Projection"
Filters
Commonly Searched Documents
-
Gratings [4.5.4]
-
Handrails [4.8.5]
Handrails are required on both sides for ramps with a rise more than 6 inches or a horizontal length more than 72 inches....
-
Station 6-Speed
Design speed is critical in determining horizontal and vertical alignments. Speed is also used in calculating necessary sight distances....
-
11B-602.6 Water flow
The angle of the water stream shall be measured horizontally relative to the front face of the unit....
-
1015.2 Where required
equipment platforms, aisles, stairs, ramps and landings that are located more than 30 inches (762 mm) measured vertically to the floor or grade below at any point within 36 inches (914 mm) horizontally...
-
1009.7.2 Separation
The fire-resistance-rated exterior wall construction shall extend horizontally 10 feet (3048 mm) beyond the landing on either side of the landing or equivalent fire-resistance-rated construction...
-
11B-602.6 Water flow
The angle of the water stream shall be measured horizontally relative to the front face of the unit....
-
Sears Brands, LLC Craftsman 24 in. Digital LaserTrac® Level
As you level all of your household projects – from building stairs to hanging mirrors – you’ll appreciate all of Craftsman’s unique functionalities....
-
DEL Motorized Solutions Remote Control Cellular Shades
This system is a great fit for almost any project because of its wide variety of options and strength and would work well for large cellular shades....
-
Notification Forms
The documentation must include the reason that full compliance could not be achieved and should be retained with the project records....
-
1.1.2 Purpose
4453 vests enforcement authority to the Director of the Department of General Services (generally delegated to the Division of the State Architect) where state funds are utilized for any project...
-
5. Ground Level PV Systems
.: There are no accessibility requirements within the area of work.12 The project is not an alteration that would trigger path of travel upgrades.13 An accessible...
-
1.1.2 Purpose
4453 vests enforcement authority to the Director of the Department of General Services (generally delegated to the Division of the State Architect) where state funds are utilized for any project...
-
1.1.2 Purpose
4453 vests enforcement authority to the Director of the Department of General Services (generally delegated to the Division of the State Architect) where state funds are utilized for any project...
-
g) New Construction and Alterations
construction and alterations . . . do not require a close-out inspection for compliance with federal disability access design standards or specific sign-off from the relevant City official that a project...
-
References:
IDeA Center at the University of Buffalo, New York: The Wheeled Mobility Anthropometry Project, Final Report, pages 89-92. D’Souza, et al....
-
Clear Width [4.13.5] and Vertical Clearance
In alterations, a projection up to 5/8 inch is permitted for the latch-side stop where it would otherwise be necessary to widen a door....
-
3.3 Need for "Overriding" Principle
The concept and the research project through which we arrived at our performance recommendations will be expanded upon at length in the last section of this paper....
-
11B-812.8.7 Location
Signs shall be permanently posted either immediately adjacent to the vehicle space or within the projected vehicle space width at the head end of the vehicle space....
-
11B-812.8.7 Location
Signs shall be permanently posted either immediately adjacent to the vehicle space or within the projected vehicle space width at the head end of the vehicle space....
-
Architect
It also has a top jamb mounted configuration that can maintain the 78" aff for Barrier Removal projects with 6'-8" doors....
-
11B-233.1 General
What is the number of residential dwellings units in a public housing project that trigger compliance with Chapter 11B?...
-
American Specialties Coat and Bumper Hook 0714
Chrome-plated 3" (75 mm) projection. Rubber bumper protects wall surface....
-
Research Issues
And that’s the research project grants and the small business grants....
