I don't think this is a contradiction, just a higher standard for stairs which need to meet requirements for stairs which are considered part of the accessible means of egress. ...
Search Results "Best Meets"
-
Re: Stair widths
-
Ground Surfaces
The Department is aware that there is an ongoing controversy about play area ground surfaces arising from a concern that some surfaces that meet the ASTM requirements at the time of installation...
-
Door King Inc. DKS Easy Setup For Vehicular Slide Gate Operators
Requires the Registered User plan or above. Login! -
International Society of Wheelchair Professionals (ISWP)
The International Society of Wheelchair Professionals (ISWP) was launched in February 2015 with a mission to provide wheelchair users worldwide with the best technology and service....
-
5 Key Warranty Features to Compare Before Hiring a Roofer
When searching for the Best Roofing Companies Philadelphia enables you to find contractors who offer workmanship warranties of 10, 20, or even 25 years, far superior to the standard one...
-
Accessible Means of Entry to Spas
Sections 242.4 and 1009.2, 1009.4, and 1009.5 of the 2010 Standards require spas to meet accessibility requirements, including an accessible means of entry....
-
F247.2 Existing Trails
Where the original design, function, or purpose of an existing trail is changed and the altered portion of the trail directly connects to a trailhead or another trail that substantially meets...
-
7(2)(a)
(a) Bathrooms that have reinforced walls for grab bars (see Requirement 6) would meet section 100.205(c)(3)(iv) if: Note: Cabinets under lavatories are acceptable provided the bathroom...
-
Staff Training
Staff Training Providing good training to your staff is perhaps the single most important step you can take towards meeting your ADA obligations....
-
Drinking Fountains and Water Coolers [4.15]
Units that meet conventional industry standards are acceptable for providing access to people who have difficulty bending or stooping....
-
F247.2 Existing Trails
Where the original design, function, or purpose of an existing trail is changed and the altered portion of the trail directly connects to a trailhead or another trail that substantially meets...
-
604.5 Grab Bars
Reinforcement must be sufficient to permit the installation of rear and side wall grab bars that fully meet all accessibility requirements including, but not limited to, required length,...
-
III-4.1200 Safety
ILLUSTRATION: A wilderness tour company may require participants to meet a necessary level of swimming proficiency in order to participate in a rafting expedition....
-
Are closet doors and pantry doors required to comply?
Doors to shallow closets or pantries, cabinets and other storage elements not providing user passage do not have to comply with provisions for doors, but must meet requirements for storage...
-
§ 37.5(i)(3) Public entity-public transport
This requirement applies to the means public entities use to meet their obligations under all provisions of this part....
-
§ 37.101(e) Demand Responsive System, Vehicle Capacity of 16 or Fewer
These entities are required to ensure that their systems, when viewed in their entirety, meet the equivalent service requirements of §§37.171 and 37.105, regardless of whether or not the...
-
§ 37.5(i)(3) Public entity-public transport
This requirement applies to the means public entities use to meet their obligations under all provisions of this part....
-
Issue: Program Accessibility
Common Problem: City governments often have failed to ensure that the whole range of the city’s services, municipal buildings, and programs meet Title II’s program access requirements...
-
5.2.1.4 Transfer Surface Size Recommendations for Imaging Equipment (M301)
All X-ray tables meet the 28-inch table width....
-
B.2.ii. - How should an agency proceed in identifying "applicable" technical provisions in Subparts B, C, and D of the Access Board’s standards to ensure acquired products provide comparable access?
Acquired products that meet the specific technical provisions set forth in Subpart B will also meet the broader functional performance criteria in Subpart C....
-
Before January 26, 1992
Keep in mind, however, that sometimes making architectural changes is the best solution financially or administratively, or because it furthers the ADA’s goal of integration. 25 28...
-
M101.6 Dimensional Tolerances (Section-by-Section Analysis)
Where available, tolerances are best addressed by industry standards for the specific materials and methods employed in the manufacturing process....
-
TITLE III COVERAGE
The Parties agree that it is in their best interests, and the United States believes that it is in the public interest, to voluntarily enter into this Agreement....
-
5.3.2.2 Transfer Sides Recommendation for Imaging Equipment
Industry agreed the best solution is to have transfer access where feasible within the medical equipment design on both long sides....
