Permanent seats at the head end of the bathtub shall be 15 inches (380 mm) deep minimum and shall extend from the back wall to or beyond the outer edge of the bathtub....
Search Results "Permanent Structure"
Commonly Searched Documents
-
610.2 Bathtub Seats
-
11B-610.2 Bathtub seats
Permanent seats at the head end of the bathtub shall be 15 inches (381 mm) deep minimum and shall extend from the back wall to or beyond the outer edge of the bathtub....
-
610.2 Bathtub Seats
Permanent seats at the head end of the bathtub shall be 15 inches (380 mm) deep minimum and shall extend from the back wall to or beyond the outer edge of the bathtub....
-
106.5.66 Structural Impracticability
106.5.66 Structural Impracticability....
-
Soft Contained Play Structure
A play structure made up of one or more play components where the user enters a fully enclosed play environment that utilizes pliable materials, such as plastic, netting, or fabric....
-
SOFT CONTAINED PLAY STRUCTURE
[DSA-AC] A play structure made up of one or more play components where the user enters a fully enclosed play environment that utilizes pliable materials, such as plastic, netting, or fabric...
-
SOFT CONTAINED PLAY STRUCTURE
[DSA-AC] A play structure made up of one or more play components where the user enters a fully enclosed play environment that utilizes pliable materials, such as plastic, netting, or fabric...
-
610.4 Structural Strength
610.4 Structural Strength....
-
§ 36.401(c) Exception for structural impracticability.
(c) Exception for structural impracticability....
-
§ 35.151(a)(2) Exception for structural impracticability
(2) Exception for structural impracticability....
-
11B-1002.4.3 Gaps
Exception: Where compliance is not operationally or structurally feasible, ramps, bridge plates, or similar devices complying with the applicable requirements of 36 CFR 1192.83(c) shall...
-
106.5.62 Soft Contained Play Structure
A play structure made up of one or more play components where the user enters a fully enclosed play environment that utilizes pliable materials, such as plastic, netting, or fabric....
-
M305.2.2 Structural Strength
Transfer supports and their connections shall be capable of resisting vertical and horizontal forces of 250 pounds (1,112 N) applied at all points on the transfer support.
-
610.4 Structural Strength
stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or supporting structure...
-
610.4 Structural Strength
stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or supporting structure...
-
Structural Impracticability (Preamble, Section-by-Section Analysis)
Structural Impracticability Proposed § 36.401(c) is included in the final rule with minor changes....
-
Sec.36.401(c) Exception for structural impracticability
(c) Exception for structural impracticability....
-
III-7.3120 Temporary structures
III−7.3120 Temporary structures (ADAAG §4.1.1(4)). Temporary buildings that are extensively used or are essential for public use are covered....
- Figure 610.2 Bathtub Seats – Drawing from the U.S. Access Board
-
11B-610.4 Structural strength
11B-610.4 Structural strength....
-
Single Occupant Structures (§203.6)
Single Occupant Structures (§203.6) Single occupant structures accessed only by below-grade passageways or elevated above standard curb height Examples: toll booths that are accessed...
-
Structural Impracticability (Section-By-Section Analysis and Response to Comments)
Structural Impracticability (Section-By-Section Analysis and Response to Comments) Proposed Sec.36.401(c) is included in the final rule with minor changes....
-
§104.23(c)(3)
(3) This section does not require recipients to make building alterations that have little likelihood of being accomplished without removing or altering a load-bearing structural member....
-
11B-610.4 Structural strength
stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or supporting structure...