A public accommodation may not impose a surcharge on a particular individual with a disability or any group of individuals with disabilities to cover the costs of measures, such as the provision...
Search Results "Measuring Instrument"
-
§ 36.301(c) Charges
-
4.7.2 Slope
The slope shall be measured as shown in Fig. 11. Transitions from ramps to walks, gutters, or streets shall be flush and free of abrupt changes....
-
Changes in Level - Accessible Route Tool
Changes in Level - Accessible Route Tool This handy tool was developed by Evan Terry Associates to assist its surveyors in measuring changes in level along an accessible route....
-
11B-608.2.3 Alternate roll-in type shower compartments
Alternate roll-in type shower compartments shall be 36 inches (914 mm) wide and 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
American Specialties Surface Mounted Roll Paper Towel Holder 8165
Unit measures 13" (330 mm) wide and projects 4 7/8" (125 mm) from wall....
-
Access-Able Designs Tub Transfer Bench SH-414-LR
Measures 29" W x 15" D x 21"D. Custom sizes available. 5 year warranty....
-
Sec.36.607(a)(2)
By the same token, certification would not be relevant to construction of a facility for children, if the regulations against which equivalency is measured do not address children's facilities...
-
605.2 Height and Depth
Urinals shall be 13½ inches (345 mm) deep minimum measured from the outer face of the urinal rim to the back of the fixture....
-
802.3.1 Alignment
The shoulder alignment point of the wheelchair space shall be measured 36 inches (915 mm) from the front of the wheelchair space....
-
605.2 Height and Depth
Urinals shall be 13½ inches (345 mm) deep minimum measured from the outer face of the urinal rim to the back of the fixture. Figure 605.2 Height and Depth of Urinals...
-
11B-404.2.4.3 Recessed doors and gates
457 mm) of the latch side at an interior doorway, or within 24 inches (610 mm) of the latch side of an exterior doorway, projects more than 8 inches (203 mm) beyond the face of the door, measured...
-
11B-705.1.1.2 Dome spacing
detectable warning surface shall have a center-to-center spacing of 2.3 inches (58 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch (16.5 mm) minimum, measured...
-
11B-404.2.4.3 Recessed doors and gates
457 mm) of the latch side at an interior doorway, or within 24 inches (610 mm) of the latch side of an exterior doorway, projects more than 8 inches (203 mm) beyond the face of the door, measured...
-
Instructions
Survey Tools and Techniques explains how to make certain measurements required to complete the Checklist....
-
DETR
., 2000) was limited to measurement of device size and weight....
-
3.3.2 Unoccupied Device Length
unoccupied length for a powered wheelchair in our sample was 52 mm (2 in.) greater than the unoccupied length of the reference chair given in the standards, and the longest unoccupied length measured...
-
American Specialties Folding Shower Seat 8206-L
Seat measures 33" (840 mm) wide and projects 22 7/8" (580 mm) from wall....
-
§ 36.606(a)(2)
By the same token, certification would not be relevant to construction of a facility for children, if the regulations against which equivalency is measured do not address children´s facilities...
-
4 [§ 4.7.2]
To measure the gutter slope, place the level in the same position as the arrow in the illustration, with one end where the gutter meets the ramp and the other end towards the street....
-
703.2.5 Character Height
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
R305.2 Placement
Where the back of curb edge is tooled to provide a radius, the border dimension should be measured from the end of the radius....
-
4.1.6(4)(d)
(ii) If existing thresholds measure 3/4 in (19 mm) high or less, and are beveled or modified to provide a beveled edge on each side, then they may be retained....
-
§ 37.135(d) Phase-in of implementation
If the date for full compliance specified in the plan is after January 26, 1993, the plan shall include milestones, providing for measured, proportional progress toward full compliance....
