Protruding Objects Baby changing tables cannot violate the protruding object requirements of TAS 204 and 307 in either an open or closed position since either position is a potential...
Search Results "Horizontal Position"
Filters
Commonly Searched Documents
-
Protruding Objects
-
1132A.3, Item 2
Swinging doors shall provide a net clear opening width of not less than 32 inches (813 mm), measured with the door or doors positioned at an angle of 90 degrees from the closed position....
-
11B-206.2.9.1 Load and unload areas
Where load and unload areas have more than one loading or unloading position, at least one loading and unloading position shall be on an accessible route....
-
1132A.3, Item 2
Swinging doors shall provide a net clear opening width of not less than 32 inches (813 mm), measured with the door or doors positioned at an angle of 90 degrees from the closed position....
-
11B-206.2.9.1 Load and unload areas
Where load and unload areas have more than one loading or unloading position, at least one loading and unloading position shall be on an accessible route....
-
11B-206.2.9.1 Load and unload areas
Where load and unload areas have more than one loading or unloading position, at least one loading and unloading position shall be on an accessible route....
-
Jeff's Story - A Video about Living with Spina Bifida
Requires the Registered User plan or above. Login! -
Medical Diagnostic Equipment Accessibility Standards Sub Committee Recommendations Stretcher Final Report
Specifically, Section M301, Diagnostic Equipment Used by Patients in Supine, Prone, or Side-Lying Position....
-
404.2.8.1 Door Closers and Gate Closers
Door closers and gate closers shall be adjusted so that from an open position of 90 degrees, the time required to move the door to a position of 12 degrees from the latch is 5 seconds minimum...
-
4.6.3 Eyepiece
The eyepiece for the telescope or periscope that is usable from a seated position for viewing each point of interest shall be positioned 43 inches (1090 mm) minimum and 51 inches (1295 mm...
-
505.10.2 Top Extension at Stairs
At the top of a stair flight, handrails shall extend horizontally above the landing for 12 inches (305 mm) minimum beginning directly above the first riser nosing....
-
f-v
If a ramp is more than 30 feet long, is a level landing at least 60 inches long provided at every 30 feet of horizontal length?...
-
4d.
If a ramp is more than 30 feet long, is a level landing at least 60 inches long provided every 30 feet of horizontal length?...
-
6d. Ramp Length
If a ramp is more than 30 feet long, is a level landing at least 60 inches long provided every 30 feet of horizontal length?...
-
Extensions
Handrails that are not continuous must have horizontal extensions at both the top and bottom of the ramp at least 12 inches long that are rounded or returned smoothly to walls, posts, or...
-
11B-809.10.5.2 Reinforcement for grab bars
Grab bar backing shall be installed horizontally to permit the installation of a 48-inch (1219 mm) grab bar with each end 6 inches (152 mm) maximum from the end walls of the bathtub....
-
Pilot Rock CN-AMQ Amherst Collection Square Ash Receptacles
Specifications: Model CN-AMQ Ash Receptacle is fabricated with 10 ga. steel vertical and horizontal straps. ...
-
Handrail Requirements
An exception permitted brackets and balusters attached to the bottom of a handrail provided they did not obstruct more than 20% of the handrail length, their horizontal projection was at...
-
206.2.9.1 Load and Unload Areas
Where load and unload areas have more than one loading or unloading position, at least one loading and unloading position shall be on an accessible route....
-
404.2.8.1 Door Closers and Gate Closers
Door closers and gate closers shall be adjusted so that from an open position of 90 degrees, the time required to move the door to a position of 12 degrees from the latch is 5 seconds minimum...
-
3. Buttock-Popliteal Length
Buttock-Popliteal Length For this study, an estimate of buttock-popliteal length was calculated as the horizontal distance from the proximal (rear) edge of the wheelchair seat cushion...
-
404.2.10 Door and Gate Surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other. Cavities created by added kick plates shall be capped....
-
711.3.2 Membrane penetrations
By a horizontal distance of not less than 24 inches (610 mm); 1.2....
-
404.2.10 Door and Gate Surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other....
