Transfer surfaces shall be adjustable in height measured from the floor to the top of the uncompressed transfer surface and shall provide the following: A....
Search Results "Mitigating Measures"
Filters
Commonly Searched Documents
-
M301.2.1 Adjustability
-
M302.2.1 Adjustability
Transfer surfaces shall be adjustable in height measured from the floor to the top of the uncompressed transfer surface and shall provide the following: A....
-
Floor Designations
The proposed rule specified that tactile floor designations at the hoistway be 60 inches above the floor, measured from the baseline of the characters (407.2.4)....
-
Accessible Pool Stairs
ADAAG provisions for stairs include the requirement that all steps have uniform riser heights and uniform tread widths of not less than 11 inches, measured from riser to riser....
-
§104.44(c) Course examinations
student's achievement in the course, rather than reflecting the student's impaired sensory, manual, or speaking skills (except where such skills are the factors that the test purports to measure...
-
7(2)(b)(vii)
If the shower stall is the only bathing facility provided in the covered dwelling unit, or on the accessible level of a covered multistory unit, and measures a nominal 36 x 36, the shower...
-
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
2 Method
The two main dependent measures were: Whether the detectable warnings could be seen from distances between 2.44 m (8ft) and 7.92 m (26 ft)....
-
903.4 Back Support
Back support shall be 2 1/2 inches (64 mm) maximum from the rear edge of the seat measured horizontally. ...
-
11B-604.7.1 Dispensers
Toilet paper dispensers shall comply with Section 11B-309.4 and shall be 7 inches (178 mm) minimum and 9 inches (229 mm) maximum in front of the water closet measured to the centerline of...
-
§ 38.125(b)(8) Platform entrance ramp
The entrance ramp, or loading-edge barrier used as a ramp, shall not exceed a slope of 1:8, when measured on level ground, for a maximum rise of 3 inches, and the transition from station...
-
§ 38.83(b)(8) Platform entrance ramp
The entrance ramp, or loading-edge barrier used as a ramp, shall not exceed a slope of 1:8 measured on level ground, for a maximum rise of 3 inches, and the transition from the station platform...
-
§ 38.95(b)(8) Platform entrance ramp
The entrance ramp, or loading-edge barrier used as a ramp, shall not exceed a slope of 1:8, when measured on level ground, for a maximum rise of 3 inches, and the transition from station...
-
11B-604.7.1 Dispensers
Toilet paper dispensers shall comply with Section 11B-309.4 and shall be 7 inches (178 mm) minimum and 9 inches (229 mm) maximum in front of the water closet measured to the centerline of...
-
VI. CERTIFYING STATE ACCESSIBILITY CODES
In an effort both to facilitate compliance with all applicable laws and to mitigate the tension between federal and state enforcement processes, the ADA authorizes the Department of Justice...
-
Hospital and healthcare settings. (Section-by-Section Analysis)
A direct threat is defined as a significant risk to the health or safety of others that cannot be eliminated or mitigated by a modification of polices, practices, or procedures. ...
-
Bobrick Recessed Toilet Tissue Dispensers B-697
Double roll model measures 12 5⁄16" W x 6 1⁄8" H (315 x 155mm). Mounting: clamps for securing to stud walls or countertop aprons....
-
Bobrick Recessed Toilet Tissue Dispensers B-6977
Double roll model measures 12 5⁄16" W x 6 1⁄8" H (315 x 155mm). Mounting: clamps for securing to stud walls or countertop aprons....
-
American Specialties Folding Shower Seat 8208-R
Seat measures 33" (840 mm) wide and projects 22 7/8" (580 mm) from wall....
-
Trimco 1102 Series Cast Pull
The 1102 Pulls are ADA compliant and measure 5-1/2″ CTC. They are available in most architectural finishes to match just about any design....
-
Doorbell Factory Square Stainless Steel Doorbell
Solid 3/16" thick Stainless Steel Plate Comes with non-lighted push button and mounting screws Measures 3" W x 3" H square Usually ships in 1-3 business days...
-
Bobrick Recessed Toilet Tissue Dispenser B-6697
Single-roll model measure 6 1⁄8" W x 6 1⁄8" H (155 x 155mm)....
-
McGuire Associates Disability Evacuation Plan (DEP)
The Americans with Disabilities Act (ADA) mandates that all emergency evacuation plans include measures to ensure the safe evacuation of people with disabilities....
-
Knee & Toe Space [M303.2.4]
Each of these measurements creates a more accessible piece of imaging equipment balanced with the physical attributes and operation of the equipment....
