opening (one door or one active leaf of a double door) at least 32"?...
Search Results "Door Surface"
Filters
Commonly Searched Documents
-
Section D: Entrances
-
11B-411.4.1 Car dimensions
Inside dimensions of elevator cars and clear width of elevator doors shall comply with Section 11B-407.4.1....
-
11B-216.4.1 Exit doors
Signs required by Chapter 10, Section 1013.4 at doors to exit passageways, exit discharge, and exit stairways shall comply with Sections 11B-703.1, 11B-703.2, 11B-703.3, and 11B-703.5....
-
11B-504.4 Tread surface
Stair treads shall comply with Section 11B-302. Changes in level are not permitted. Exception: Treads shall be permitted to have a slope not steeper than 1:48.
-
11B-504.4 Tread surface
Stair treads shall comply with Section 11B-302. Changes in level are not permitted. Exception: Treads shall be permitted to have a slope not steeper than 1:48.
-
Re: 404.2.6 Doors in Series and Gates in Series
My understanding is that it was written to keep wheelchair users from having to fight two doors at once. ...
-
Is there a minimum distance between changes in level?
span vertical changes greater than ½”, must have level landings and clearances at the tops and bottoms of each run to provide adequate separation and resting intervals between sloping surfaces...
-
Besam SL500 A02 for sustainable automatic doors
The automatic sliding door Besam SL500 from ASSA ABLOY Entrance Systems has directional sensors. The door optimizes closing to reduce energy loss after passing through the door....
-
1.2.1 Walks and other non - ramp surfaces
1.2.1 Walks and other non - ramp surfaces. When overall running slope for walks is measured according to Section 1.1.3 a recommended tolerance for running slope is +1%....
-
T302 Walking Surfaces
[See subsections ...]
-
D. Clear Floor Space
If there is a vestibule without fully automatic doors, is there a 30"x48" clear floor space where one can be outside the swing of a hinged door (i.e.: for out-swinging doors, at least 7'...
-
Surfaces (R302.7) (Section-by-Section Analysis)
Surfaces (R302.7) (Section-by-Section Analysis) The proposed technical requirements for surfaces apply to pedestrian access routes, including curb ramps and blended transitions, and accessible...
-
C. Clear Floor Space
When there is a vestibule into the public or employee restroom that does not have fully automatic doors, is there a 30"x48" clear floor space where one can be outside the swing of a hinged...
-
Can stair handrail extensions overlap door maneuvering clearances?
No, handrails and other elements cannot overlap door maneuvering clearances....
-
505.8 Surfaces
Handrail gripping surfaces and any surfaces adjacent to them shall be free of sharp or abrasive elements and shall have rounded edges....
-
505.8 Surfaces
Handrail gripping surfaces and any surfaces adjacent to them shall be free of sharp or abrasive elements and shall have rounded edges....
-
505.8 Surfaces
Handrail gripping surfaces and any surfaces adjacent to them shall be free of sharp or abrasive elements and shall have rounded edges....
-
M303.2.5 Surfaces
Wheelchair space surfaces shall not slope more than 1:48 in any direction....
-
M303.2.5 Surfaces
Wheelchair space surfaces shall not slope more than 1:48 in any direction....
-
Stabilizer Solutions StaLok Material Waterless Natural Pavement
Its unique surface characteristics resist weathering from water....
-
11B-404.2.7 Door and gate hardware
Existing locks shall be permitted in any location at existing glazed doors without stiles, existing overhead rolling doors or grilles, and similar existing doors or grilles that are designed...
-
11B-404.2.7 Door and gate hardware
Exceptions: Existing locks shall be permitted in any location at existing glazed doors without stiles, existing overhead rolling doors or grilles, and similar existing doors or grilles...
-
4.5.4 Gratings
If gratings are located in walking surfaces, then they shall have spaces no greater than 1/2 in (13 mm) wide in one direction (see Fig. 8(g))....
-
4.5.4 GRATINGS
If gratings are located in walking surfaces, then they shall have spaces no greater than 1/2 in (13 mm) wide in one direction (see Fig. 8(g))....
