Aisles and aisle accessways serving a room or space used for assembly purposes shall comply with Section 1029. [DSA-AC] In addition to the requirements of this section, means of...
Search Results "Ramp Width"
Filters
Commonly Searched Documents
-
1018.2 Aisles in assembly spaces
-
SECTION 1018 AISLES
[See subsections ...]
-
1018.2 Aisles in assembly spaces
[DSA-AC] In addition to the requirements of this section, means of egress, which provide access to, or egress from, buildings or facilities where accessibility is required for...
-
11B-904.3.1 Aisle
Aisles shall comply with Section 11B-403.
-
11B-404.2.3 Clear width
Door openings shall provide a clear width of 32 inches (813 mm) minimum....
-
M303.3.3 Ramped (Section-by-Section Analysis)
technical requirements for running slope, cross slope, clear width, edge protection, and handrails....
-
Features of Accessible Parking Spaces
If the accessible route is located in front of the parking space, install wheel stops to keep vehicles from reducing the clear width of the accessible route below 36 inches. 3....
-
404.2.3 Doorways - Clear Width
Door openings shall provide a clear width of 32 inches (815 mm) minimum....
-
11B-404.2.3 Clear width
Door openings shall provide a clear width of 32 inches (813 mm) minimum....
-
11B-404.2.3 Clear width
Door openings shall provide a clear width of 32 inches (813 mm) minimum....
-
4.8.4* Landings
Ramps shall have level landings at bottom and top of each ramp and each ramp run. Landings shall have the following features:...
-
DSA Drawing 11B-406-7C Curb Ramp Adjoining a Parking Access Aisle next to a Curb and Gutter (2016 CBC)
Requires the Premium User plan or above. (Login or upgrade your account!) -
Figure 406.6 Diagonal or Corner Type Curb Ramps – Drawing from the U.S. Access Board
-
§ 37.42(f)
vertical gap is more than 5/8 inch, measured when the vehicle is at rest, the horizontal and vertical gaps between the car floor and the boarding platform must be mitigated by a bridge plate, ramp...
-
410.6 Doors and Gates
End doors and gates shall provide a clear width 32 inches (815 mm) minimum. Side doors and gates shall provide a clear width 42 inches (1065 mm) minimum....
-
5 [§ 4.7.2]
5 [§ 4.7.2] The transitions on and off the curb ramp are the points where the gutter meets the bottom of the ramp and where the top of the ramp meets the sidewalk....
-
Common Use Circulation Paths in Employee Work Areas
also contain exceptions to the technical requirements for accessible routes for circulation paths in employee work areas: • Machinery and equipment are permitted to reduce the clear width...
-
Is there a minimum distance between changes in level?
Ramps and curb ramps, which must be used to span vertical changes greater than ½”, must have level landings and clearances at the tops and bottoms of each run to provide adequate separation...
-
Doorways [4.8.4]
Recommendation: Ramps and doors should be configured to facilitate wheelchair maneuvering and to prevent open doors from obstructing ramp openings (important along egress routes)....
-
11B-410.6 Doors and gates
End doors and gates shall provide a clear width 32 inches (813 mm) minimum. Side doors and gates shall provide a clear width 42 inches (1067 mm) minimum....
-
11B-410.6 Doors and gates
End doors and gates shall provide a clear width 32 inches (813 mm) minimum. Side doors and gates shall provide a clear width 42 inches (1067 mm) minimum....
-
9.a [§ 4.7.5]
9.a [§ 4.7.5] If the sidewalk at the top of the ramp (“x” in the illustration) is 48 inches wide or more, answer this question....
-
R304.3.2 Running Slope
The running slope of the curb ramp shall be in-line with the direction of sidewalk travel....
