EXCEPTION: Accessible ramps complying with 4.8 or, if no other alternative is feasible, accessible platform lifts complying with 4.11 may be used in lieu of an elevator....
Search Results "Ramp Length"
Filters
Commonly Searched Documents
-
4.1.2(5)
-
Simplified Building Concepts: ADA - Building an Upright
Video demonstration for building an upright for railings using Simplified Building products.
-
Simplified Building Concepts: Assembling the ADA Railing
Simplified Building Concepts: Assembling the ADA Railing
-
Simplified Building Concepts: ADA - Message to Contractors
Find out how you can use Kee Access ADA components to expand your contracting business
-
Simplified Building Kee Access ADA Railings
Kee Access fittings are used to construct ADA and smooth surface railings
-
1132A.4, Item 3
Changes in height greater than ½ inch (12.7 mm) shall be accomplished by means of a ramp complying with Section 1114A or by means of a platform constructed to the level of the floor as illustrated...
-
505.4 Height
Top of gripping surfaces of handrails shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum vertically above walking surfaces, stair nosings, and ramp surfaces....
-
4.1.6(1)(f)
(f) If an escalator or stair is planned or installed where none existed previously and major structural modifications are necessary for such installation, then a means of accessible...
-
Non-Positive Shut-off
People are always asking what the term non-positive shut-off means. It's not well-documented but I believe that it refers to a handheld valve that makes the shower head continue to...
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
Cross Slope and Surfaces [4.8.6]
Ramp surfaces must comply with requirements for ground and floor surfaces and be "stable, firm, and slip-resistant." A specific level of slip-resistance is not mandated....
-
5.9.2 Standing Supports on Ramped Entry Raised Platforms with Wheelchair Spaces
5.9.2 Standing Supports on Ramped Entry Raised Platforms with Wheelchair Spaces....
-
citEcar ADA Electric Shuttle 11P 1WC
It includes our ADA package which has a wheelchair ramp with lights and wheelchair tie downs installed on the vehicle....
-
citEcar ADA Enclosed Shuttle 11P 1WC
It includes our ADA package which has a wheelchair ramp with lights and wheelchair tie downs installed on the vehicle....
-
5.8.1.2.2 Single Ramped Entry - Edge Protection on the Platform and Platform Sides Recommendations
5.8.1.2.2 Single Ramped Entry - Edge Protection on the Platform and Platform Sides Recommendations The Committee recommends a two-inch high edge protection on the back of the platform...
-
Problem Three (Accessible Route)
Solution: Install a portable ramp....
-
11B-505.9 Fittings
Handrails shall not rotate within their fittings.
-
505.9 Fittings
Handrails shall not rotate within their fittings.
-
505.9 Fittings
Handrails shall not rotate within their fittings.
-
505.9 Fittings
505.9 Fittings. Handrails shall not rotate within their fittings.
