Eco-Grip Flooring Routing and Heat Welding...
Search Results "Vehicle Floor Coordination"
Filters
Commonly Searched Documents
-
Eco-Grip Flooring Video 4 of 8 Routing and Heat Welding
-
Running Slope of Ramps Deployed to Roadways or Curb-Height Bus Stops
Low floor buses have a lower vehicle floor (typically 15 inches or less above the roadway) that permits a flat – rather than stepped – area at doorways....
-
Eco-Grip Flooring Video 5 of 8 Inside and Outside Corners
Eco-Grip Flooring Inside and Outside Corner Installation...
-
11B-805.2.2 Beds
[2010 ADA Standards] 805.3 Clear Floor or Ground Space. A clear floor space complying with 305 shall be provided on each side of the bed....
-
Door Swing: ADA Standard Section 304.4
Section 304.4 covers the current ADA Standards for doors swinging into turning spaces.
-
11B-206.4.1 Entrances
All entrances shall comply with Section 11B-404. [2010 ADA Standards] 206.4.1 Public Entrances. In addition to entrances required by 206.4.2 through 206.4.9, at least 60 percent...
-
11B-812.5.3 Relationship to accessible routes
Vehicle spaces and access aisles shall be designed so that when the vehicle space is occupied the required clear width of adjacent accessible routes is not obstructed....
-
11B-812.5.3 Relationship to accessible routes
Vehicle spaces and access aisles shall be designed so that when the vehicle space is occupied the required clear width of adjacent accessible routes is not obstructed....
-
11B-812.7 Access aisle
Two vehicle spaces or one parking space and one electric vehicle charging space shall be permitted to share a common access aisle....
-
11B-302.2 Carpet
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge....
-
11B-302.2 Carpet
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge....
-
11B-302.2 Carpet
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge. Carpet edge trim shall comply with Section 11B-303....
-
TECHNICAL QUESTIONS:
[See subsections ...]
-
T405 Steps
[See subsections ...]
-
T403 Lifts
[See subsections ...]
-
T212 Seat Belts and Shoulder Belts
[See subsections ...]
-
12184(c)(1) Exception
(1) Exception To the extent that compliance with subsection (a)(2)(C) or (a)(7) of this section would significantly alter the historic or antiquated character of a historical or...
-
§ 38.81(a)
(a) Any stepwell or doorway with a lift, ramp or bridge plate immediately adjacent to the driver shall have, when the door is open, at least 2 foot-candles of illumination measured...
-
§ 38.23(d)(6) Stowage
(6) Stowage. When not being used for securement, or when the securement area can be used by standees, the securement system shall not interfere with passenger movement, shall not...
-
11B-812.8.4 Ambulatory
Ambulatory EVCS shall not be required to be identified by an ISA.
-
11B-812.8.6 Finish and size
Identification signs shall be reflectorized with a minimum area of 70 square inches (45,161 mm2).
-
11B-812.8.4 Ambulatory
Ambulatory EVCS shall not be required to be identified by an ISA.
-
11B-812.8.6 Finish and size
Identification signs shall be reflectorized with a minimum area of 70 square inches (45161 mm2).
-
11B-606.2 Clear floor space
A clear floor space complying with Section 11B-305, positioned for a forward approach, and knee and toe clearance complying with Section 11B-306 shall be provided. Exceptions: 1....
