The MDE NPRM proposed that the measurement of the height of the transfer surface for both diagnostic equipment used in the supine, prone, or side-lying position and diagnostic equipment...
Search Results "Standing Surface"
Commonly Searched Documents
-
(4) Adjustability: Method of Measurement
- Figure 505.6 Horizontal Projections Below Gripping Surface – Drawing from the U.S. Access Board
- Husky 10" Multi-Function Standard Digital Level
- Sears Brands, LLC Craftsman 10 in. Digital LaserTrac® Level
-
11B-405.3 Cross slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
11B-405.3 Cross slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
11B-405.3 Cross slope
Cross slope is the slope of the surface perpendicular to the direction of travel....
-
Seat Width Evaluation
many participants (the 25th through 95th percentiles) for their level, highest and lowest height transfer regardless of the presence or absence of grab bars or a backrest on the transfer surfaces...
-
7.2.2.1 Determining Impracticability
The surface is not firm and stable for a distance of 45 feet or more (14 m). Limiting Factor 3. ...
-
Light Rail Platform Slope
The Board has explicitly specified that rail platforms shall slope no more than 1:48 in any direction, consistent with cross slope provisions for walking surfaces in section 403....
-
Executive Summary
After traveling over each surface, subjects were asked to subjectively rate each surface and decide whether the surface was acceptable or not....
-
Pemko 193 Slip resistance
Hello ETA, I see that you can ask for slip resistance by adding a coating to the Pemko 193 plate. Any experience with this application? Is this a permanent slip resistance or...
- Access Board: Accessible Route Carpet
-
11B-306.2.3 Minimum required depth
The toe clearance shall extend 19 inches (483 mm) minimum under built-in dining and work surfaces required to be accessible. ...
-
Non-Circular Cross Sections: ADA Standard Section 505.7.2
Section 505.7.2 covers the current ADA Standards for the non-circular cross section of handrail gripping surfaces.
-
11B-505.7.2 Non-circular cross sections
Handrail gripping surfaces with a non-circular cross section shall have a perimeter dimension of 4 inches (102 mm) minimum and 6¼ inches (159 mm) maximum, and a cross-section dimension of...
-
11B-306.2.3 Minimum required depth
The toe clearance shall extend 19 inches (483 mm) minimum under built-in dining and work surfaces required to be accessible by Section 11B-226.1....
-
11B-306.2.3 Minimum required depth
The toe clearance shall extend 19 inches (483 mm) minimum under built-in dining and work surfaces required to be accessible by Section 11B-226.1....
-
Can stair treads and risers be perforated?
Stair treads must meet requirements for floor or ground surfaces which specify that surface openings not allow passage of a sphere more than ½ inch in diameter (§302.3)....
- Wooster Products Anti-Slip Safety Coatings Systems
-
Medical Diagnostic Equipment Accessibility Standards Sub-Committee Recommendations Imaging Equipment
Sections M302, Diagnostic Equipment used by Patients in Seated Position; M303, Diagnostic Equipment used by Patients Seated in a Wheelchair; and M304, Diagnostic Equipment used by Patients in Standing...
-
Clear Floor or Ground Space: ADA Standard Section 902.4.1
A clear floor space complying with 305 positioned for forward approach shall be provided. Knee and toe clearance complying with 306 shall be provided, except that knee clearance 24...
- Steelcase Series 3 Height-Adjustable Work Surface with Crank
- Landscape Forms Inc. Morrison Table and Stool Collection Video
