EXCEPTION: Where the surface is other than concrete, asphalt, or boards, cross slopes not steeper than 1:20 shall be permitted when necessary for drainage....
Search Results "Surface Smoothness"
Filters
Commonly Searched Documents
-
1017.8.3 Slope
-
Section C: Exterior Route
(§303) C3 Is the route free of surface openings greater than 1/2", such as grates or holes in the pavement?...
-
Pilot Rock TQ700 Square Frame Square Utility Table
Surface mount installation only (Anchor bolts not included - use Model ANC3-4 Anchor Kit). FINISH: All steel frame components have a powder coat finish in your choice of color....
-
Pilot Rock T700 Square Frame Rectangular Utility Table
Surface mount installation only (Anchor bolts not included - use Model ANC3-4 Anchor Kit). FINISH: All steel frame components have a powder coat finish in your choice of color....
-
KirbyBuilt Providence Picnic Table with Maximum Seating
100" l x 61.25" w x 32" h TableTop Dimensions 72" l x 48" w x 32" h Seat Dimensions 72" & 48" l x 9.5" w x 18" h Mount Type Portable/Surface...
-
A5.1 General
Dining counters (where there is no service) are typically found in small carry-out restaurants, bakeries, or coffee shops and may only be a narrow eating surface attached to a wall....
-
R&D Workshop Trim-A-Slab Expansion Joint Repair
Trim-A-Slab is a replacement for rotted and old wood typically found between slabs in driveways and sidewalks. This wood was used during the slab construction, and is part of the...
-
Stabilizer Solutions StaLok Stabilizer Joint Sand
STABILIZED JOINT SAND THAT STAYS PUT BETWEEN PAVERS StaLok Paver Sand sets up strong and locks in between pavers. It allows water to drain and ‘heals’ itself. The sand repairs...
-
GAP ARMOUR
GAP ARMOUR IS AN INNOVATIVE RUBBER MATERIAL ...that easily installs (with a rubber hammer) into open concrete expansion joints to completely seal and protect! Gap Armour can be...
-
Handrails Along Walkways
Handrails Along Walkways. The 1991 Standards do not contain any technical requirement for handrails provided along walkways that are not ramps. Section 403.6 of the 2010 Standards...
-
1017.7 Slopes
The slopes of trails shall comply with 1017.7.
-
Slope Ratio
Slope Ratio—A ratio of vertical distance to horizontal distance or rise to run.
-
Trail Construction Techniques
Information that is already available to Forest Service employees is not repeated in this guidebook. The "Trail Construction and Maintenance Notebook" includes practical techniques...
-
2. Methodology
[See subsections ...]
-
1017.7 Slopes
The slopes of trails shall comply with 1017.7.
-
5.4.8 Transfer Support Gripping Surface Hazard for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.8 Transfer Support Gripping Surface Hazard for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
Pilot Rock AT Series Traditional A-Frame Picnic Table With Steel Braces - Using Recycled Plastic
OPTIONAL: Attach to surface for permanent installation with optional anchor brackets. Use Model ANG-2 Angle Anchor Kit....
-
Pilot Rock Square Frame Square Table - Series TQ703
Surface mount installation only (Anchor bolts not included). Use Model ANC3-4 Anchor Kit. FINISH: All steel frame components have a powder coat finish in your choice of color....
-
Transfer Surface Height (M301.2.1 and M302.2.1)
surface....
-
904.2 Approach
All portions of counters required to comply with 904 shall be located adjacent to a walking surface complying with 403. Advisory 904.2 Approach....
-
904.2 Approach
All portions of counters required to comply with 904 shall be located adjacent to a walking surface complying with 403. Advisory 904.2 Approach....
-
904.2 Approach
All portions of counters required to comply with 904 shall be located adjacent to a walking surface complying with 403. Advisory 904.2 Approach....
-
Pilot Rock TPT Series End Accessible Twin Pedestal Table
TPT/P frame posts have a 3/8” x 10” sq. steel bolt down base plate for surface mounting (anchor bolts not included). Use Model ANC5-4 Anchor Kit - requires 2 kits....
-
M302.2 Transfer Surface (Section-by-Section Analysis)
This is an introductory section.
