Clearances for wheelchair spaces shall comply with Section 11B-1002.4.4. Exceptions: Where provided, securement devices shall be permitted to overlap required clearances....
Search Results "Patient Seated in Wheelchair"
Commonly Searched Documents
-
11B-1002.4.4 Clearances
-
5.1.4 Transfer Surface Height Measurement
The transfer surface height should be measured from the floor to the highest point on the seat in an uncompressed state, inclusive of bolsters....
-
M305.2.1 Location
Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the...
-
M305.2.4 Cross Section
Transfer supports shall have a cross section complying with 305.2.4.1 or 305.2.4.2.
-
M305.2.3 Height
During use, the tops of transfer support gripping surfaces shall be 6 inches (150 mm) minimum and 19 inches (485 mm) maximum higher than the top of the associated uncompressed...
-
M305.2.6 Gripping Surface
Transfer support gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides. The bottoms of transfer support gripping surfaces...
-
M305.2.4 Cross Section (Section-by-Section Analysis)
The proposed rule did not provide specific requirements for the cross section of transfer supports. However, in the MDE NPRM preamble, the Access Board noted that it was considering...
-
5.4.5 Transfer Support Position Recommendation for M301 and M302
5.4.5 Transfer Support Position Recommendation for M301 and M302 Description: Transfer support position refers to the placement of the gripping surface within the minimum and...
-
5.4.2 Transfer Support Length for M301 and M302
5.4.2 Transfer Support Length for M301 and M302 Description: Transfer support length applies to the gripping surface of the support, that portion of the support used to grasp or...
-
5.3 Transfer Sides
5.3 Transfer Sides.
-
5.3 Transfer Sides Recommendations
5.3 Transfer Sides Recommendations
-
M305.2.1 Location
Transfer supports shall be located within reach of the transfer surface and shall not obstruct transfer onto or off of the surface when in position.
- Zurn Z5958 Series Commercial White, Closed Front Toilet Seat with Cover
-
Wheelchair Space Overlap in Assembly Areas
Section 802.1.5 of the 2010 Standards provides that where a main circulation path is located in front of a row of seats that contains a wheelchair space and the circulation path is wider...
-
608.4 Seats
608.4 Seats. A folding or non-folding seat shall be provided in transfer type shower compartments....
-
5.3.3 Seats
Pit toilet seats shall comply with 5.3.3...
-
5.3.2.1 Transfer Sides Recommendation for Stretchers
As a result, with current stretcher design, a patient will access the long side of the transfer surface and the short side will be inaccessible....
- Bemis 1955CT Heavy Duty Open Front Less Cover Commercial Toilet Seat
-
M301.4 Lift Compatibility
subcommittee recommended the alternate means of using an overhead lift instead of providing clearances for portable lifts because: 1) a ceiling mounted lift can have advantages for better patient...
- Tork Toilet Seat Cover Dispenser
-
608.4 Seats
A folding or non-folding seat shall be provided in transfer type shower compartments....
-
608.4 Seats
A folding or non-folding seat shall be provided in transfer type shower compartments....
-
Other Issues Relating to Seat Assignments
Other Issues Relating to Seat Assignments You must provide a seat assignment accommodation when requested by a passenger with a disability even if the seat is not otherwise available...
-
Transfer Protocols
Her weight and height were 210 lbs and 66 inches respectively and she lacked the ability to transfer to surfaces that were not at the same level as her wheelchair seat to floor height....