The Department seeks input regarding the impact the measures being contemplated by the Department with regard to accessible equipment and furniture will have on small entities if adopted...
Search Results "Mitigating Measures"
-
Question 23
-
7c.
Is there clear maneuvering floor space in front of each accessible door (see Figure 25 in the appendix for measurements) and on the pull side, is there at least 18 inches clear floor space...
-
M303.2.6 Edge Protection
Where wheelchair spaces are provided on a platform raised more than 1 ½ inches (38 mm) in height, edge protection 2 inches (51 mm) high minimum measured from the surface of the platform...
-
11B-703.8.7 Character spacing
Spacing shall be measured between the two closest points of adjacent low resolution VMS characters within a message, excluding word spaces....
-
Tools and Documentation
The following tools are needed for the 2016 Checklist: a metal tape measure at least 20 feet long a digital level or a bubble level that is at least 24 inches long a door pressure...
-
705.1.2 Dome Spacing
detectable warning surface shall have a center-to-center spacing of 1.6 inches (41 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch (17 mm) minimum, measured...
-
Running Slope (Grade)
The ascent or descent of a trail segment expressed as a percentage of its length, which is the difference in elevation of a section of a trail measured parallel to the predominant direction...
-
4.9.2 TREADS AND RISERS
Stair treads shall be no less than 11 in (280 mm) wide, measured from riser to riser (see Fig. 18(a)). Open risers are not permitted on accessible routes....
-
11B-703.8.7 Character spacing
Spacing shall be measured between the two closest points of adjacent low resolution VMS characters within a message, excluding word spaces....
-
605.2 Height and Depth
Urinals shall be 13 1/2 inches (345 mm) deep minimum measured from the outer face of the urinal rim to the back of the fixture....
-
705.1.2 Dome Spacing
detectable warning surface shall have a center-to-center spacing of 1.6 inches (41 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch (17 mm) minimum, measured...
-
Sections 35.108(d)(1)(v) and 36.105(d)(1)(v)—Comparisons to Most People in the Population, and Impairment Need Not Prevent or Significantly or Severely Restrict a Major Life Activity
In that example, evidence gathered to demonstrate the impairment of a learning disability showed a discrepancy between the person’s age, measured intelligence, and education and that person...
-
Actions which Constitute Discrimination
Failing to use employment tests in the most effective manner to measure actual abilities....
-
B. Experts’ Responsibilities
In addition to reviewing and analyzing surveys and remedial measures, the Experts will assess the quality and sufficiency of Harris County’s survey process and implementation of remedial...
-
ADA Gap Tool
ADA Gap Tool This handy tool was developed by Evan Terry Associates to assist its surveyors in measuring gaps in ground or floor surfaces....
-
502.6 Identification
Signs shall be 60 inches (1525 mm) minimum above the finish floor or ground surface measured to the bottom of the sign....
-
Side Reach [§308.3]
The maximum reach depth for this range is 10” measured from the available clear floor space....
-
§ 37.139(d)(5)
The plan shall include milestones for implementing phases of the plan, with progress that can be objectively measured yearly;...
-
11B-813.2.1.3 Height and operation
Adult changing table height shall be adjustable from 17 inches (432 mm) above the floor or ground to 38 inches (965 mm) above the floor or ground, as measured to the top of the changing...
-
1009.2.4 Seat Height
The height of the lift seat shall be designed to allow a stop at 16 inches (405 mm) minimum to 19 inches (485 mm) maximum measured from the deck to the top of the seat surface when in the...
-
1.5 Materials
The reflectance factors were measured on a different day using a Minolta CS-100 Chroma Meter....
-
4.1 Wheeled Mobility Device Dimensions
Thus, specifying exactly how it is measured is important for comparing results....
-
11B-202.4 Path of travel requirements in alterations, additions and structural repairs
In order to mitigate existing barriers, it is first necessary to identify them....
-
11B-202.4 Path of travel requirements in alterations, additions and structural repairs
In order to mitigate existing barriers, it is first necessary to identify them....